« previous next »
Pages: [1]   Go Down

Author Topic: How can I modify a grooved scope receiver to a weaver mount.  (Read 2271 times)

0 Members and 2 Guests are viewing this topic.

Offline montveil

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 343
  • Gender: Male
How can I modify a grooved scope receiver to a weaver mount.
« on: August 31, 2008, 10:00:12 AM »
How can I modify a grooved scope receiver to a weaver mount.

Thanks

Montveil
Logged
MONTVEIL IN THE NC MOUNTAINS

Offline rbergum95

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 373
  • Gender: Male
  • Theres no luck in lead unless it's flyin'.
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #1 on: August 31, 2008, 02:52:34 PM »
have it drilled and tapped for weaver mounts by a competent gunsmith.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #2 on: August 31, 2008, 03:04:16 PM »
B-Square makes a 3/8" dovetail to Weaver adapter.

Tim

http://www.rrarms.com/catalog.php?prod=BS17025
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Brithunter

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2538
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #3 on: September 01, 2008, 12:23:42 AM »
Errr why not just buy some decent mounts and save the hassle?

using an adaptor adds another layer of tolerences so the possibility of more errors. Drilling and tapping does the same really so if it's grooved already why not use them with proper mounts?
Logged

Offline Glanceblamm

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2814
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #4 on: September 01, 2008, 03:34:53 AM »
Weaver makes (or used to make) what they called a 1" tip-off mount. These are just Standard rings that will clamp on the grooved reciever but allow for a 1" tubed scope to be installed on the top side. I hope that I am in the ballpark regarding your question...This is a low profile rock solid setup when it comes to the grooved reciever. I have a set on the WMR plus a reg L.R.
Logged

Offline HotRod9mm

  • Trade Count: (0)
  • Member
  • *
  • Posts: 38
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #5 on: September 14, 2008, 08:19:09 PM »
For what rifle?

I made my own for the CZ 452/453
Logged

Offline woodchukhntr

  • GBO Supporter
  • Trade Count: (108)
  • Senior Member
  • *****
  • Posts: 2359
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #6 on: September 15, 2008, 01:23:38 AM »
Another alternative that is even more solid than the 1" Tip-off mount is a mount meant for airguns.  It mounts like the Weaver adaptor shown, but has the rings as part of the base.  It is really rock solid since it has a long bearing area on the 3/8" dovetail.  B-Square makes one, as well as RWS and even Crosman.
Logged

Offline Glanceblamm

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2814
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #7 on: September 16, 2008, 04:08:41 AM »
Quote from: HotRod9mm on September 14, 2008, 08:19:09 PM
For what rifle?

I made my own for the CZ 452/453

HotRod9mm
Welcome To Graybeard Outdoors!
Nice work on those mounts that you made and I can smell a CNC mill for sure?
I would love to own one of these as I did ok in two consecutive classes. I still use the computer program just to keep my skills...My classes were not CNC specific but were required as part of an Engineering/Electrical & Instrument degree. Those CNC mills & lathes sure were fun though.
Logged

Offline Skeeter27red

  • Trade Count: (0)
  • Posts: 1
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #8 on: October 06, 2008, 09:23:41 PM »
Quote from: HotRod9mm on September 14, 2008, 08:19:09 PM
For what rifle?

I made my own for the CZ 452/453


Thank goodness you made enough for all of us to enjoy! Hotrod9mm's CZ/Anschutz Weaver adapter rails rock!
  Just the thing for my 453 Varmint!.......Oh, and don't forget the action screws He makes as well, all top shelf and it DOES come with a matching wood screw, FLUSH mount, and a first class finish on that Torx head too! :)
  He told me He'd have ALL of the screws for virtually any CZ rimfire within the next coupla weeks. Now I can get my action screw torque "Just right" everytime.

http://www.rimfiretechnologies.com/ProductDetails.asp?ProductCode=CZ%2DS10
Logged

Offline HotRod9mm

  • Trade Count: (0)
  • Member
  • *
  • Posts: 38
Re: How can I modify a grooved scope receiver to a weaver mount.
« Reply #9 on: October 07, 2008, 04:09:41 AM »
Quote from: glanceblamm on September 16, 2008, 04:08:41 AM
HotRod9mm
Welcome To Graybeard Outdoors!...


Thanks. The main reason I did mine was I got tired of waiting for CZ to get more rails in stock(over a year now).
 I put one on my "Trainer" so I can use my Mueler APV with Burris Zee Quick Detach rings and still use the iron sights.

Not the best pic but you get the idea...
Logged
Pages: [1]   Go Up
« previous next »