Author Topic: Home made cast bullets  (Read 818 times)

0 Members and 1 Guest are viewing this topic.

Offline Cheesehead

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 3282
  • Gender: Male
Home made cast bullets
« on: September 02, 2008, 04:57:04 PM »
Anyone use home made cast bullets with sabots in their in lines? I have tried this with 330 grain 458 cal. Good accuracy at 50 yards. Have not tried it at 100 yet.

Cheese
Nothing in the world is more dangerous than sincere ignorance.

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #1 on: September 04, 2008, 01:56:59 PM »
I cast up some 292 gr lead  ( 458 for 45-70 ) and got clover leaf at 50 yds,  (savage 700MLSS, 209 w/39 gr 5744 ) than I went to a 405 HB 2 to 3" group at 120 yards. I am satisfied. Today I cast a few 520 gr and cant wait to get back to the range. I cant find a load for the 520 so I'll start with 32 gr 5744.
                                               Dan

Offline Cheesehead

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 3282
  • Gender: Male
Re: Home made cast bullets
« Reply #2 on: September 04, 2008, 02:37:56 PM »
Thanks for the reply Dan. Sounds like good results for you. I have also been using 5744 with good results in my Savage. I need more range time. Been using MMP sabots for the 458 slugs. Cant wait to get a deer in my sights.

Cheese
Nothing in the world is more dangerous than sincere ignorance.

Offline kb

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 336
  • Gender: Male
Re: Home made cast bullets
« Reply #3 on: September 05, 2008, 05:52:17 AM »
Are you using cast?  What load?  Inquiring minds........
If electricity comes from electrons, does morality come from morons?

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #4 on: September 06, 2008, 01:53:14 PM »
I have been casting my own, I cast for 45-70 and when I bough the savage last year and found that I can get sabots for a 457 bullet. So I cast a bunch of 300, 320, 340, and 405 from soft lead. I did manage to retrive a coupla of them and they were wider than they were long.
  I cronyed the 405's at 1880 FPS . I used 39 gr of 5744 for all these loads.
 Tomorrow I will post my results with a 500 gr bullet.  Dan

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #5 on: September 07, 2008, 12:05:06 PM »
 OK, I went to the range today to try some 458, 520 gr bullets with MMP orange sabots.   At 125 yards, my worst group was 2 1/4 ". I used 39 gr of 5744. I was a little concerend with recoil so I started with 34 gr and worked my way up to 39 . I am very satisified with this load. I did forget to take the crony . Dan

Offline Cheesehead

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 3282
  • Gender: Male
Re: Home made cast bullets
« Reply #6 on: September 07, 2008, 01:52:43 PM »
Great results Dan. What type of lead are you using. I have been using 100% wheel weights and have been considering pure lead, for expanding purposes.

Cheese
Nothing in the world is more dangerous than sincere ignorance.

Offline moto357

  • Trade Count: (10)
  • Avid Poster
  • **
  • Posts: 196
Re: Home made cast bullets
« Reply #7 on: September 08, 2008, 12:39:05 PM »
i vote pure lead for the speeds shot out of any ML, even da smokeless smokepoles ;D

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #8 on: September 08, 2008, 01:52:30 PM »
I use pure lead, I have a small selection of molds for my 45-70 and I use w/w, for
the savage I went to pure lead because I like the expansion. I did recover some 405's and one 520, the 405 was quite wide, the 520 is the size of a 50 cent coin
 and weighed 505 gr. Now, these were shot with a dirt back stop. I can't wait till muzzle loader season. Dan

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #9 on: September 08, 2008, 01:55:52 PM »
moto357.....I taught you everything you know about MUZZLE LOADERS, next week I"ll give you a bullet.

Offline moto357

  • Trade Count: (10)
  • Avid Poster
  • **
  • Posts: 196
Re: Home made cast bullets
« Reply #10 on: September 09, 2008, 12:52:26 AM »
how long till i can play with powder??? :o

Offline rangerwillie

  • GBO Supporter
  • Trade Count: (29)
  • Avid Poster
  • *****
  • Posts: 178
Re: Home made cast bullets
« Reply #11 on: September 09, 2008, 11:07:42 AM »
2015

Offline moto357

  • Trade Count: (10)
  • Avid Poster
  • **
  • Posts: 196
Re: Home made cast bullets
« Reply #12 on: September 10, 2008, 05:54:10 AM »
can i at least smash some caps with a hammer? ???