« previous next »
Pages: [1]   Go Down

Author Topic: .223 Bullet seating and other problems..........  (Read 485 times)

0 Members and 1 Guest are viewing this topic.

Offline Dan308

  • Trade Count: (0)
  • Member
  • *
  • Posts: 12
  • Gender: Male
    • Dtknives
.223 Bullet seating and other problems..........
« on: December 02, 2008, 12:41:15 PM »
Please help me, my head is starting to get clouded with numbers

My Handi .223 bull 1:12 twist is not liking anything I load. I've been reloading for over 20 yrs but this time I can't get lucky. Here is what I've found. To seat a 55gr VMAX to touch the lands is 2.442 OAL. My load is 26.0 BLc-2, 55gr VMAX seated to 2.380 OAL. This load will group about .910 @ 100 yards.

I would like to seat to be off the lands .015 - .020 but at 2.380 there is only .177 of bullet in the case.

Varget did not shoot better than 1.75 inches. BLc-2 seems to be better, but 26.0 is a mild load.

Any suggestions on which way to go?

Dan308
Logged

Offline Troyboy

  • GBO Supporter
  • Trade Count: (41)
  • Senior Member
  • *****
  • Posts: 1220
  • Gender: Male
  • Work more talk less
Re: .223 Bullet seating and other problems..........
« Reply #1 on: December 02, 2008, 01:36:05 PM »
Have you asked on the handi forum? One of the poeple there will know
Logged
.204 .22lr .22wm .25acp .223 5.56 .243 .25-06 6.5x55  .308  .300wbymag  7.5x54  7.62x25 7.62x39  338-06  9x19 .38spl  9x18 .45acp . 45-70 .500s&w 12rfl 12smb 20smb  .45lc 410smb .22hornet .280AI    Ask not what your country can do for you BUT what can YOU do for your country

Offline Dan308

  • Trade Count: (0)
  • Member
  • *
  • Posts: 12
  • Gender: Male
    • Dtknives
Re: .223 Bullet seating and other problems..........
« Reply #2 on: December 02, 2008, 03:24:20 PM »
oh, I was thinking it was more of a .223 reloading question.
Logged

Offline Badnews Bob

  • Trade Count: (34)
  • Senior Member
  • *****
  • Posts: 2963
  • Gender: Male
Re: .223 Bullet seating and other problems..........
« Reply #3 on: December 02, 2008, 03:41:13 PM »
You find most handies have long throats, also the 1-12"  ones seem to like lighter bullets, but you'll deffinatly find out more in the NEF forum. We be a little nutz there. ;)
Logged
Badnews Bob
AE-2 USN retired

Offline jhalcott

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1869
Re: .223 Bullet seating and other problems..........
« Reply #4 on: December 02, 2008, 05:03:51 PM »
  I spent several years trying to work up a sub inch load for a .25-06, THAT gun was so inaccurate I had it rebarreled! I could NOT bring my self to inflict it on any one else. Also ,there are very few sub inch guns in the bargain grade group.Have you tried any LONGER bullets in it? I suppose you have taken a chamber cast to be certain that the chamber/bore alignment is right?! A gunsmith showed me a casting he took of a Savage rifle. The chamber/bore were so misaligned that Savage rebarreled the gun FREE.
Logged
Pages: [1]   Go Up
« previous next »