« previous next »
Pages: [1]   Go Down

Author Topic: need bullet mold for 38/55 .380-.382  (Read 1332 times)

0 Members and 1 Guest are viewing this topic.

Offline brennemanj83

  • Classified -- Banned
  • Trade Count: (3)
  • Contributor
  • *
  • Posts: 362
  • Gender: Male
need bullet mold for 38/55 .380-.382
« on: December 07, 2008, 12:33:13 PM »
i'm trying find a bullet mold for my 38/55 in 250-300gr with a diameter of .380-.382.does anyone know where i can find one or is this going to be a custom mold?  JON
Logged
Banned for less than honest trading practices.

Offline Nrut

  • Trade Count: (2)
  • Member
  • *
  • Posts: 70
Re: need bullet mold for 38/55 .380-.382
« Reply #1 on: December 07, 2008, 02:46:49 PM »
Check Buffalo Arms website...They carry a lot of molds for BPCR...If they don't have what you want you can have LTB or MT. Molds make you one that will fit your rifle..
Logged

Offline ktw

  • Trade Count: (0)
  • Member
  • *
  • Posts: 40
Re: need bullet mold for 38/55 .380-.382
« Reply #2 on: December 25, 2008, 03:22:04 PM »
The Saeco 571 (300gr, tapered) runs .3830"-.3835" on the base band. 
The slightly shorter Saeco 738 (250 gr, tapered) runs .3810"-.3820" on the base band.

I have a rifle with a .382 groove diameter.  Other than the SAECOs, I haven't found any other off-the-shelf molds that will throw a bullet this large.

One of my favorite loads in the rifle is Lyman 375449 (.377 as cast in ACWW) paper patched up to .382 (no gas check) over IMR3031.

-ktw
Logged

Offline Okie2

  • Trade Count: (0)
  • Member
  • *
  • Posts: 38
Re: need bullet mold for 38/55 .380-.382
« Reply #3 on: January 02, 2009, 04:04:08 PM »
My cheapo/generic Lee produces .381 @ 260 grains....I don't size.... it's listed as a .379 @ 250...don't know why mine produces bigger...but, I'm glad it does.... Scott
Logged

Offline walkingwolf

  • Trade Count: (4)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Re: need bullet mold for 38/55 .380-.382
« Reply #4 on: January 05, 2009, 04:43:45 AM »
  You can take a lee mold, cast a very hard bullet. Drill a hole center put a screw in cut the head off. Put valve lapping compound in the groves. In the mold with a drill you can open the mold to the size you want.
Logged
Don't smoke in bed the Assh you save may be your own

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: need bullet mold for 38/55 .380-.382
« Reply #5 on: January 16, 2009, 05:04:05 PM »
My Lee 2 cavity mould goes .384. I size them to .377 for my 375 Taylor with no problem, they'd be just what you need for a 38-55.
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."
Pages: [1]   Go Up
« previous next »