« previous next »
Pages: [1]   Go Down

Author Topic: .308 to 6.5 creedmoor  (Read 1357 times)

0 Members and 1 Guest are viewing this topic.

Offline crp

  • Trade Count: (0)
  • Member
  • *
  • Posts: 8
.308 to 6.5 creedmoor
« on: January 10, 2009, 01:56:26 PM »
I have a handi rifle in.308 and am interested in the new hornady 6.5 creedmoor cartridge. I know the cartridge is based on the .308 case so would it be possible to convert my .308 barrel to the 6.5 creed moor? If so, what would i have to have done and what would be a ball park figure for the work?
Logged

Offline Badnews Bob

  • Trade Count: (34)
  • Senior Member
  • *****
  • Posts: 2963
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #1 on: January 10, 2009, 02:00:14 PM »
No you can't do that one, the creedmore is a 6.5mm the .308 is a 7.62mm you can go up but you can't go down on bullet size.
Logged
Badnews Bob
AE-2 USN retired

Offline brennemanj83

  • Classified -- Banned
  • Trade Count: (3)
  • Contributor
  • *
  • Posts: 362
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #2 on: January 10, 2009, 02:25:49 PM »
I would start with 24'' 223 bull barrel and rebore and chamber for the 6.5 creedmore.
Logged
Banned for less than honest trading practices.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #3 on: January 10, 2009, 02:28:44 PM »
Cost will be in the neighborhood of $300 for a rebore as there is no 6.5mm bore barrel made by H&R, you could also have a stub done(see FAQs and help sticky) but the will cost about the same.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline brennemanj83

  • Classified -- Banned
  • Trade Count: (3)
  • Contributor
  • *
  • Posts: 362
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #4 on: January 10, 2009, 02:39:12 PM »
Hey Tim where could a person get a stub barrel made up at?
Logged
Banned for less than honest trading practices.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #5 on: January 10, 2009, 02:43:03 PM »
Wayne at Oregunsmithing will do rebores or stubs, he's done both for me, lots of rebores for members here.  ;)

Tim

http://home.earthlink.net/~oregunsmithing/index.html
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline brennemanj83

  • Classified -- Banned
  • Trade Count: (3)
  • Contributor
  • *
  • Posts: 362
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #6 on: January 10, 2009, 02:45:39 PM »
Tim do you have a pic of one that Wayne done?I would like to see how his look.
Logged
Banned for less than honest trading practices.

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #7 on: January 10, 2009, 02:53:33 PM »
He did my 6.5x55 from the experimental 300WSM stub and a 6.5 Shilen match barrel, you can barely see the line where the two are mated about 1/8" back from the forend.

Tim


https://www.gboreloaded.com/mhp/images/quickdtoo/6_6.jpg
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline brennemanj83

  • Classified -- Banned
  • Trade Count: (3)
  • Contributor
  • *
  • Posts: 362
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #8 on: January 10, 2009, 03:02:26 PM »
Thanks Tim.......You really are the man  ;D......That 6.5x55 is really one sweet round
Logged
Banned for less than honest trading practices.

Offline Jeff H

  • GBO Supporter
  • Trade Count: (13)
  • Contributor
  • *****
  • Posts: 258
Re: .308 to 6.5 creedmoor
« Reply #9 on: January 10, 2009, 05:10:51 PM »
Quote from: quickdtoo on January 10, 2009, 02:53:33 PM
He did my 6.5x55..............Tim

OOH!  A 6.5x55 Handi'! :o
THAT would be SO cool. 
Hanging aorund here is going to get expensive.
Logged

Offline FW Conch

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 404
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #10 on: January 10, 2009, 11:59:29 PM »
 ??? Tim ! Have we seen a range report on that jewel (6.5 x 55) yet ?   ::)  Jim
Logged
Jim

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #11 on: January 11, 2009, 05:35:54 AM »
No, ya didn't miss it, haven't made it out there yet, with the weather the way it's been and the range only open on Sundays since now, I'll need a "convergence" as Patrick McManus calls it!!  :-\

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline petemi

  • GBO Supporter
  • Trade Count: (73)
  • Senior Member
  • *****
  • Posts: 7386
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #12 on: January 11, 2009, 08:46:30 AM »
Tim, I am frustrated.  Can't drag out the bench rest, spotting scope, ammo, ear goodies,  snow blow a trail to the shooting  bench, snow blow a trail to the target, Clear the snow off the shooting bench.  Go inside the house, drink lots of hot coffee and or something else.  Come back out, set up, breathe on the scope, wait til it clears.  Now feet are cold, go in, put on dry socks and boots.  Check the thermometer....oh, not too bad...3 above.  Wind? hell, it's only 21 knots......across the range.  Spotting scope fogged.  Hand stuck to frame.  Beer froze.  When does April happen???? ??? ??? 

Oh, yeah, hot barrels are not a problem.

Pete
Logged
Keep both eyes open and make the first shot good.
The growing Handi/Sportster/Pardner/Topper Family:  .22 WMR, .22-250. 223, Two Superlight 7mm-08s and one .243, .30-30,  .308, 32-20, 18 inch .356/.358 Win., Two 16.5 inch .357 Max., 18 inch 38-55 BC Carbine, 16.5 inch .445 Super Mag., .45LC, 16.5 and 22 inch .45-70s, .50 Huntsman SS, .410, 20 ga., 12 ga., 20 ga. Pardner Pump, Versa-Pack .410 - .22
[size=7.4 pt]PLEASE DONATE TO THE GBO SERVER FUND  We're closer to the goal but not there yet, we can still use more donations, thanks

http://www.gboreloaded.com/forums/index.php/topic,191112.msg1098959491.html#msg1098959491

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #13 on: January 11, 2009, 08:54:08 AM »
I'm lucky then, just have to deal with rain, unfortunately I want the chrono set up for load work and it can't be used in the rain.  :-\ I thought about trying to waterproof it, but I think anything I do to protect the sensors would also compromise readings. ???

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Spanky

  • Moderators
  • Trade Count: (96)
  • Senior Member
  • *****
  • Posts: 4627
  • Gender: Male
  • USMC Semper Fidelis
Re: .308 to 6.5 creedmoor
« Reply #14 on: January 11, 2009, 09:05:17 AM »
Winter sucks. >:(
I hate not being able to go to the range.


Spanky
Logged

Offline petemi

  • GBO Supporter
  • Trade Count: (73)
  • Senior Member
  • *****
  • Posts: 7386
  • Gender: Male
Re: .308 to 6.5 creedmoor
« Reply #15 on: January 11, 2009, 09:15:20 AM »
I think you're right on the chrono.  Mine's going to sit on the shelf until spring.  Then, In the wintery mean time, I'll line up everything I want to chrono and do it in one fine 70 degree, sunshiny spring day with daffodils and crocuses popping out of the ground.

Pete
Logged
Keep both eyes open and make the first shot good.
The growing Handi/Sportster/Pardner/Topper Family:  .22 WMR, .22-250. 223, Two Superlight 7mm-08s and one .243, .30-30,  .308, 32-20, 18 inch .356/.358 Win., Two 16.5 inch .357 Max., 18 inch 38-55 BC Carbine, 16.5 inch .445 Super Mag., .45LC, 16.5 and 22 inch .45-70s, .50 Huntsman SS, .410, 20 ga., 12 ga., 20 ga. Pardner Pump, Versa-Pack .410 - .22
[size=7.4 pt]PLEASE DONATE TO THE GBO SERVER FUND  We're closer to the goal but not there yet, we can still use more donations, thanks

http://www.gboreloaded.com/forums/index.php/topic,191112.msg1098959491.html#msg1098959491
Pages: [1]   Go Up
« previous next »