Author Topic: Is this possible??  (Read 1585 times)

0 Members and 2 Guests are viewing this topic.

Offline Blucollar

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 139
Is this possible??
« on: April 13, 2009, 05:27:12 PM »
I have a s&w .357 model 66, it has a 4" barrel, I would like to change to a longer barrel for hunting.

Is this a reasonable idea or is it more trouble than it would be worth?

Thanks, Blu
EXCEPT a man be BORN AGAIN, he CANNOT see the kingdon of GOD.  John 3:3 kjv

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 27002
  • Gender: Male
Re: Is this possible??
« Reply #1 on: April 13, 2009, 05:33:23 PM »
The easiest and likely cheapest way would be to just trade it for a longer barrel revolver. I have both the 4" and 6" S&W 66s. Since S&W has discontinued it and no longer have barrels in stock (yeah I asked a good while back) your only real option would be to locate a barrel to be installed or have one custom made.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline rockbilly

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3367
Re: Is this possible??
« Reply #2 on: April 13, 2009, 06:37:50 PM »
The 6 5/8 inch barrelk is normally available from Numrich, they are currently out of stock but you can check with them and see when they will  be available again.  You are looking at about $225. (parts and labor) to do this change.  It might be more cost effective to to take GBs advice and trade.

     http://www.e-gunparts.com/product.asp?chrProductSKU=561340&MC=

Hope this helps. 8)

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 27002
  • Gender: Male
Re: Is this possible??
« Reply #3 on: April 14, 2009, 06:18:09 AM »
Six and 5/8" is NOT a standard S&W barrel length in any of their revolvers. The M66 is a K-frame stainless steel adjustable sight .357 revolver. It was made in snub nose configuration with about a 2.5" or so barrel as well as 4" and 6" and no others ever.

Other SS barrels made for other S&W .357" guns might could be made to fit but the cost to do so would likely exceed the cost of the barrel.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline spruce

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2248
  • Gender: Male
Re: Is this possible??
« Reply #4 on: April 14, 2009, 10:52:58 AM »
Unless you have a sentimental attachment to that particular gun I think it would be much more cost-effective to sell it and then look for a used 6" model 66 or 686.

From what I've seen lately the 4" and shorter barrels seem to be the hot sellers right now so you should be able to break even or make a little on the deal.

Offline Ak.Hiker

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 389
Re: Is this possible??
« Reply #5 on: April 14, 2009, 06:53:03 PM »
I wonder if you were to keep the 4 inch and put some money into a new sight if the gun would work for hunting? I know we have some hunting loads on the market that run pretty hot out of a 4 inch barrel. The Double Tap load with the 158 grain Gold Dot comes to mind, the Buffalo Bore 180 grain cast is another one depending on your needs.

Offline Autorim

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 610
  • Gender: Male
Re: Is this possible??
« Reply #6 on: April 15, 2009, 02:10:13 AM »
Yes, it can be done. Is it cost effective? No. IMHO, for hunting, you should consider a longer barrel and larger caliber.

Offline Blucollar

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 139
Re: Is this possible??
« Reply #7 on: April 15, 2009, 05:03:05 PM »
Thanks for the great info! It helps me alot.
The gun has been in the family for a while so I don't want to trade it.
I will probably shop around for one more suitable for hunting.
Thanks again, Blu.
EXCEPT a man be BORN AGAIN, he CANNOT see the kingdon of GOD.  John 3:3 kjv

Offline surveyor47

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 127
Re: Is this possible??
« Reply #8 on: April 17, 2009, 08:59:56 AM »
S&W K-frame magnum revolvers, the 19, 66, 65 were designed in the 1950s to provide police officers the capability of firing 357 Magnum ammo.  They were essentially 38 Specials with a LIMITED CAPACITY to fire the 357 Magnum.  Police practiced with 38 Special ammo and carrried 357 Magnums. In the 1970s, they started practicing with their 357 Magnum duty ammo, which these guns were not built to handle on a full time basis. High performance 357 ammo came along, the 125 grain jacketed hollow point, which not only did a great job as a stopper, but also as a gun destructor. S&W has advised that 125 grain ammo can crack the forcing cone of a K-frame revolver within 50 to 100 rounds and there are no replacement barrels left. They advise to shoot 38s, but if you must shoot 357s, make it 158 grain, which is the ammo these guns were designed for.  These are not hunting guns and there are much better tools for the job.  They remain one of the finest combat handguns ever built, within their limitations. A K-frame loaded with +P38 Specials is excellent in all respects. 

The Ruger Security Six is in all respects similar to the K-frames, except that they can fire approximately 3 times the number of shells as a K-frame before going back for maintainence.  While much more durable than S&W, the Ruger Security Six also suffered maintenence problems when fired full time with 357 ammo.  Both the S&W K-frames and Ruger Security Six were discontinued, replaced by the S&W 586/686 and GP100 respectively.  Both of these guns were designed as full time 357 magnums. 

For hunting, I would purchase either a 41 or 44 Magnum for game up to the size of deer.  If you intend to scope the gun, Rugers Super Redhawk or one of their limited run Blackhawks Hunters are excellent. The Ruger Super Blackhawk was designed for hunting and remains a solid choice. S&W has limited runs of hunting revolvers, costing about triple that of a Ruger.


Offline *ROCK-MAN*

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 128
  • Gender: Male
Re: Is this possible??
« Reply #9 on: April 17, 2009, 02:05:29 PM »
If you do want to be able to switch barrel sizes look at the Dan Wessons.It's an easy switch for them.
Good Luck
Rock
Walk softly,keep the wind in your face and watch your backtrail.

Offline rockbilly

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3367
Re: Is this possible??
« Reply #10 on: April 18, 2009, 07:23:53 AM »
Owning a Dan Wesson is kinda like having an ugly wife, she serves your necessary needs but is nothing to brag about. ::) ::)

Offline Blucollar

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 139
Re: Is this possible??
« Reply #11 on: April 19, 2009, 04:35:22 PM »
I think I'll check out the Ruger, Thanks again, Blu
EXCEPT a man be BORN AGAIN, he CANNOT see the kingdon of GOD.  John 3:3 kjv

Offline Old Griz

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2030
  • Gender: Male
Re: Is this possible??
« Reply #12 on: June 02, 2009, 10:41:21 AM »
Six and 5/8" is NOT a standard S&W barrel length in any of their revolvers. The M66 is a K-frame stainless steel adjustable sight .357 revolver. It was made in snub nose configuration with about a 2.5" or so barrel as well as 4" and 6" and no others ever.

Except for the 3" ;D
Griz
<*}}}><

I Cor. 2.2 "For I determined not to know anything among you, save Jesus Christ, and him crucified."

Offline Mohawk

  • Moderator
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1958
Re: Is this possible??
« Reply #13 on: June 02, 2009, 01:09:28 PM »
  A 4" barrel is fine for hunting. That's all I have ever used and never went hungry due to lack of game meat harvested. 4" with iron sights has never done me wrong yet.  :)

Offline Old Griz

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2030
  • Gender: Male
Re: Is this possible??
« Reply #14 on: June 19, 2009, 07:33:26 PM »
blucollar;
I agree with Mohawk, the 4" barrel will serve you well for hunting, however, you must check with your state regulations. Some states require a barrel over 4" to legally hunt with.

If you're gonna hunt with a .357 I'd keep things within bow hunting ranges. My 2 cents worth is to move up to a .41, or .44.
Griz
<*}}}><

I Cor. 2.2 "For I determined not to know anything among you, save Jesus Christ, and him crucified."