« previous next »
Pages: [1]   Go Down

Author Topic: reloading .32 S&W ctge  (Read 1821 times)

0 Members and 3 Guests are viewing this topic.

Offline Buckwheat Jack

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 113
  • Gender: Male
  • 45-70; 45 Long Colt; 12ga; .410
reloading .32 S&W ctge
« on: July 08, 2009, 04:21:56 PM »
Any advice on a good handload for the venerable .32 S&W? Can I use .32 H&R Mag dies?
Logged
aim small, hit big

Offline Paladin

  • Trade Count: (6)
  • Contributor
  • ***
  • Posts: 313
Re: reloading .32 S&W ctge
« Reply #1 on: July 08, 2009, 04:40:20 PM »
yes to the 32 mag dies. load depends on what your shooting them in. my old lyman43 edition starts at 3 grains of unique under a 95 grain lrn. It is wise to use more than one source of reloading data. Later
Logged

Offline Blackhawk44

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 981
Re: reloading .32 S&W ctge
« Reply #2 on: July 08, 2009, 06:55:06 PM »
On your dies, its a yes, but you cannot crimp the S&W or the S&W Long with the H&R die.  A better way to go is to use .32 ACP.  With these you can load ACP, S&W, Longs or H&R by only switching shell holders and adjusting the crimp die to length.  Recheck you cartridge again.  Data between the S&W (short) and the S&W Long is not interchangeble. 
Logged

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26946
  • Gender: Male
Re: reloading .32 S&W ctge
« Reply #3 on: July 09, 2009, 12:32:54 AM »
I think most of the .32 Mag dies are made for use with the .32 S&W long and the longer .32 H&R Magnum. Most likely yours are also and thus can be used just fine for both.
Logged


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline Larry Gibson

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1069
Re: reloading .32 S&W ctge
« Reply #4 on: July 09, 2009, 06:15:23 AM »
Quote from: Graybeard on July 09, 2009, 12:32:54 AM
I think most of the .32 Mag dies are made for use with the .32 S&W long and the longer .32 H&R Magnum. Most likely yours are also and thus can be used just fine for both.

Concur with Graybeard, most .32 dies these days are for both the .32SWL and the .32 H&R. 

As to "a good handload" the Lyman manuals are a very good source of loads.  A mention of what type of .32SWL handgun might bring more specific responses.

Larry Gibson
Logged

Offline Buckwheat Jack

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 113
  • Gender: Male
  • 45-70; 45 Long Colt; 12ga; .410
Re: reloading .32 S&W ctge
« Reply #5 on: July 09, 2009, 04:59:06 PM »
The gun I am loading for is simply a 32 S&W, the short one. It appears to be the third variation, for smokeless loads, made about 1905+-
Logged
aim small, hit big

Offline Larry Gibson

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1069
Re: reloading .32 S&W ctge
« Reply #6 on: July 09, 2009, 06:33:29 PM »
Quote from: Buckwheat Jack on July 09, 2009, 04:59:06 PM
The gun I am loading for is simply a 32 S&W, the short one. It appears to be the third variation, for smokeless loads, made about 1905+-

Sorry, I was thinking of the S&WL.  The Lyman Cast Bullet Handbook has loads for 77 & 84 gr cast bullets in the .32 S&W. A friend uses 1.3 gr of Bullseye under Speer 90 gr swaged HBWCs in his .32 S&W.  He seats them so the case mouth is very lightly crimped in the front canelure groove.  Lyman lists 1.4 gr of Bullseye as max for the 84 gr hard cast bullet.  I do know the Speer and Hornady swaged lead HBWCs are very accurate in my little M30 .32 S&WL.

I shortened his .32 S&WL/.32 H&R seating dies so it would crimp the shorter cases.
 
Larry Gibson
Logged
Pages: [1]   Go Up
« previous next »