« previous next »
Pages: [1]   Go Down

Author Topic: Nipple wrench  (Read 893 times)

0 Members and 1 Guest are viewing this topic.

Offline wormbobskey

  • Trade Count: (27)
  • A Real Regular
  • ****
  • Posts: 779
  • Gender: Male
Nipple wrench
« on: August 26, 2009, 03:13:48 PM »
Can anyone point me in the right direction to find a CVA 1851 nipple wrench?
Logged
OSTA
Lanums Animal Damage Control & Repair
We don't do bugs

Offline FourBee

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1770
  • Gender: Male
Re: Nipple wrench
« Reply #1 on: August 26, 2009, 05:45:03 PM »
Wow! wormbobskey:
I don't have the ASM CVA Schematic, so I can't varify the nipple size.
Armi San Marco CVA 1851 Navy .36 cal and .44 cal. revolvers may use the same size nipple as Pietta.   But check it out cause I'm not real certain on this one.
Cabela's used to carry the "Davide  Pedersoli "  #015 nipple wrench which fits the Pietta guns perfectly (Nipple Size 6mm x .75mm).   The last time I purchased from them it came with a set of 6 nipples for $21.  This is a tough little wrench.  Others I've bought broke easily, or were too large and stripped off the nipples as most wrenches are softer than the nipple.  
Logged
Enjoy your rights to keep and bear arms.

Offline wormbobskey

  • Trade Count: (27)
  • A Real Regular
  • ****
  • Posts: 779
  • Gender: Male
Re: Nipple wrench
« Reply #2 on: August 27, 2009, 02:19:11 AM »
I've got a "standard" nipple wrench for my rifles, but its way to big to fit into the recessed area around the nipples. I'll check out your suggestion and also check and see if CVA has one they sell.
Logged
OSTA
Lanums Animal Damage Control & Repair
We don't do bugs

Offline coyotejoe

  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 2937
  • Gender: Male
Re: Nipple wrench
« Reply #3 on: August 27, 2009, 04:45:09 AM »
Track of the Wolf sells a revolver nipple wrench which will fit about any revolver except the little 1862 Colt, I've had to modify wrenches for those.
Logged
The story of David & Goliath only demonstrates the superiority of ballistic projectiles over hand weapons, poor old Goliath never had a chance.

Offline wormbobskey

  • Trade Count: (27)
  • A Real Regular
  • ****
  • Posts: 779
  • Gender: Male
Re: Nipple wrench
« Reply #4 on: August 27, 2009, 05:03:28 AM »
Thanks, coyotejoe. I'll look them up.
Logged
OSTA
Lanums Animal Damage Control & Repair
We don't do bugs

Offline NozzleRag

  • Trade Count: (0)
  • Member
  • *
  • Posts: 21
Re: Nipple wrench
« Reply #5 on: August 28, 2009, 11:05:09 AM »
Quote from: FourBee on August 26, 2009, 05:45:03 PM
Wow! wormbobskey:
I don't have the ASM CVA Schematic, so I can't varify the nipple size.
Armi San Marco CVA 1851 Navy .36 cal and .44 cal. revolvers may use the same size nipple as Pietta.   But check it out cause I'm not real certain on this one.
Cabela's used to carry the "Davide  Pedersoli "  #015 nipple wrench which fits the Pietta guns perfectly (Nipple Size 6mm x .75mm).   The last time I purchased from them it came with a set of 6 nipples for $21.  This is a tough little wrench.  Others I've bought broke easily, or were too large and stripped off the nipples as most wrenches are softer than the nipple.  

The Possible Shop has a new racheting nipple wrench that is a pleasure to use.
Logged
Pages: [1]   Go Up
« previous next »