« previous next »
Pages: [1]   Go Down

Author Topic: Contender sling stud  (Read 1035 times)

0 Members and 2 Guests are viewing this topic.

Offline yorketransport

  • Trade Count: (13)
  • Avid Poster
  • **
  • Posts: 205
Contender sling stud
« on: September 06, 2009, 09:36:24 AM »
Didn't somebody make a replacement grip screw with a built in sling stud? I've searched, but come up with nothing. I want to have a two point sling for my Contender, but I need a rear swivel stud.

Andrew
Logged
Shipping FedEx Ground keeps a small business running.

I'm not late, I'm early for tomorrow.

Keep honking, that should fix everything.

Offline Hopalong7

  • Trade Count: (20)
  • Senior Member
  • *****
  • Posts: 1673
  • Gender: Male
Re: Contender sling stud
« Reply #1 on: September 06, 2009, 11:21:59 AM »
     Go to foxridgeoufitters.com.
Logged

Offline Bullseye

  • Trade Count: (9)
  • Senior Member
  • *****
  • Posts: 1879
Re: Contender sling stud
« Reply #2 on: September 08, 2009, 06:45:03 AM »
Uncle Mikes.
Logged

Offline Hopalong7

  • Trade Count: (20)
  • Senior Member
  • *****
  • Posts: 1673
  • Gender: Male
Re: Contender sling stud
« Reply #3 on: September 08, 2009, 07:16:14 AM »
     Uncle Mike's(Lyman) makes the kit for the Contender, but when I called them recently they told me that the only place they knew of I could get one was from Fox Ridge.  It hadn't been too long since I had called Fox Ridge and had been told they didn't have them.  But, since they did show on their web site, I called them again.  At first they seemed quite confused as to whether they did or didn't have them, but finally told me they did and I DID get two of the kits from them.  This was about 3 months ago.  Good luck.
   
Logged

Offline yorketransport

  • Trade Count: (13)
  • Avid Poster
  • **
  • Posts: 205
Re: Contender sling stud
« Reply #4 on: September 09, 2009, 05:02:18 PM »
Thanks for the replies everyone. I'll give Fox Ridge a call.

Andrew
Logged
Shipping FedEx Ground keeps a small business running.

I'm not late, I'm early for tomorrow.

Keep honking, that should fix everything.

Offline Lager

  • Trade Count: (13)
  • Avid Poster
  • **
  • Posts: 129
Re: Contender sling stud
« Reply #5 on: September 13, 2009, 02:42:59 PM »
Excuse my ignorance about Contenders, Im new here and just bought mine used and I have this thing sticking out out the bottom of my grip.It has a hole in it and could be used to mount a sling to.
Is this what you are talking about?
Yorketransport, If you are having troubles finding it? You can have mine. I find it very annoying. Just send me the original screw,thats in good shape and I will send you this one.
Logged

Offline Ladobe

  • Trade Count: (91)
  • Senior Member
  • *****
  • Posts: 3193
Re: Contender sling stud
« Reply #6 on: September 13, 2009, 11:36:28 PM »
Yep, that would be an extended grip screw made for attaching a sling.   And yep, with no sling attached they are a bit of a PITA.
Logged
Evolution at work. Over two million years ago the genus Homo had small cranial capacity and thick skin to protect them from their environment. One species has evolved into obese cranial fatheads with thin skin in comparison that whines about anything and everything as their shield against their environment. Meus

Offline canoe

  • Trade Count: (0)
  • Posts: 4
Re: Contender sling stud
« Reply #7 on: October 29, 2009, 02:14:50 AM »
I also need one of the grip through bolts with the built in stud.  I looked on the Fox Ridge site and did not see one.  I called and the folks I talked with did not seem to know anything about such a bolt.  Anyone have a part number or a solution.  Thanks, Brian.
Logged

Offline canoe

  • Trade Count: (0)
  • Posts: 4
Re: Contender sling stud
« Reply #8 on: October 29, 2009, 03:40:55 AM »
Just found my answer to the above post.  About gave up looking for the part and went through Brownells catalog one more time.  The swivel set with special through bolt is available as a kit.  It is a seperate listing not found with the standard Uncle Mikes fit-met chart.  Brian.
Logged

Offline Anduril

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 335
Re: Contender sling stud
« Reply #9 on: October 29, 2009, 03:54:12 AM »
Brian,
and the Brownells part number is ........ ?
..
Logged

Offline canoe

  • Trade Count: (0)
  • Posts: 4
Re: Contender sling stud
« Reply #10 on: October 29, 2009, 07:19:36 AM »
From Catalog #62 (2009-2010) page 202, part # 3E23Y86.  Price is $29.82 for the kit.  Hope this helps.  Brian.
Logged

Offline ftw

  • GBO Supporter
  • Trade Count: (1)
  • Avid Poster
  • *****
  • Posts: 183
  • Gender: Male
Re: Contender sling stud
« Reply #11 on: October 30, 2009, 01:24:19 PM »
Thanks, someone is always looking for these. Actually 593-000-005AC is the part number to search Brownells for.
Logged
Inside of every Old Man is a Kid saying "What the Heck Happened"

Frank
Pages: [1]   Go Up
« previous next »