Author Topic: Midsouth Shooters Supply Varmint Nightmare Bullet Review  (Read 20675 times)

0 Members and 2 Guests are viewing this topic.

Online Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26905
  • Gender: Male
Midsouth Shooters Supply Varmint Nightmare Bullet Review
« on: October 08, 2009, 06:12:07 PM »
MSS Varmint Nightmare Bullet Review

www.midsouthshooterssupply.com

Midsouth Shooters Supply a GBO Sponsor has been selling bullets under their name and calling them Varmint Nightmare for at least a couple years now. I’ve bought some from them in the past for my .17 Fireball though I’ve not tried them yet and bought some of the 50 grain .224” SPs as well and have used those in the past. In fact the 50 grain SP has proved to be my most accurate hand load so far for my Remington 700 SPS Varmint rifle in .22-250. I’ve not done extensive load development for that rifle yet either but my first series with it using H380 and the MSS 50 grain Nightmare delivered groups hovering right at the half inch mark at 100 yards. I called it good for then as I had a prairie dog shoot to go to and just didn’t have time to do further testing at the time. Sadly I’ve not gotten back to it for further development yet but with a load that shoots like that it just hasn’t been a priority.

The same 50 grain bullet has worked well in some loads for my pair of .223 Remington Varmint rifles I took to a previous shoot as well. I’d have to hunt hard to locate the specifics on those loads but suffice to say they were up to the task for prairie dog shooting.

I had a marathon shooting session this morning (10-08-09) firing a total of 100 rounds from two rifles for a total of 20 five shot groups. Over all I was a bit disappointed that groups were no smaller but some were quite excellent and some were rather dismal. I did shoot fast and the barrels did get hot and at times mirage was a factor so might be a partial excuse for the larger groups.
 
I did learn the chamber of the Model Seven Predator is much tighter than the M700 SPS Varmint as with all rounds chambering was more difficult and all rounds were full length sized. Over all the SPS shot more accurately but I guess that was no surprise. Loads were not specifically worked up for either rifle just pulled from manuals at random and put together. I think smallest five shot group was around a half inch and largest around two inches. Most were around 1.2” or less. Within the larger five shot groups many three and four shot clusters were quite tight perhaps indicating my shooting or the mirage was at fault not the ammo or rifles. With AA2460 powder all groups with the SPS varmint were well under an inch whereas in the Model Seven that group shot the second worst of all so what one rifle liked had little bearing on what the other liked and really proved to me the overall results mostly just indicated I need to work up specific loads for each rifle with the MSS bullets to see just how well the bullets can perform.

Within some of the not so great five shot groups based on max spread of the full five shots I had several with sub clusters of three and four shots that measured a mere quarter of an inch center to center. Those loads are definitely worth exploring more for those rifles as I’m sure my hurried pace and/or the mirage from barrel heat made that one shot go wide that changed an otherwise super tight group into a so-so group for five shots. That some loads turned in five shot half inch and less groups tells me the bullets are clearly up to the task.
 
It also showed me what I’ve seen in the past and that is that I prefer 40 and 50 grain bullets over 55 grain in the .223 and that all the shooting I’ve done so far with all my rifles in .223 it seems all preferred the lighter bullets over the 55s though some groups with the 55s have proved to be very good indeed. I just tend to have more of those really good groups with 40s and 50s no matter the bullet maker.
 
I’ve now shot their (MSS)  55 grain bullets in three rifles in two chamberings (.223 and .22-250) and can form some opinions on the bullets. They seem to work as well as anyone’s and do cost considerably less than most and seem to be in stock most of the time. I think they are an excellent choice especially so for volume shooting in ARs and such due to their economy and they do shoot as well as any other standard bullet in my experience.

Currently they offer .224” 55 grain bullets in quantities of 500 or 2000, .224” 50 grain SP in 500 count boxes, 55 grain .224 Premium SP and HP bullets in 500 count boxes as well as a 34 grain flat base HP .224” bullet also in 500 packs. They also have bullets for your .204 Ruger rifles, a 34 grain flat base HP and for your .17s they have a 20 grain .172” flat base HP and as with the rest they sell them in 500 count boxes. Current catalog prices run from $35.24 to $44.67 per 500 but prices are subject to change so do be sure to check for current pricing. Still some premium bullets run that much or more per 100 and these are well made accurate bullets from my experience to date.

Some highlights from today’s marathon shooting session showed my SPS Varmint really liked these 55s with AA2460. I loaded three loads at 23.0, 24.0 and 25.0 grains and seated bullets to 2.250” C.O.L. Groups respectively averaged 0.9”, 0.50” and 0.75” for five shots at 100 yards. Not bad for loads just pulled from a book and not yet tweaked for the rifle.

By way of contrast the Model Seven Predator shot those same loads into 2.0”, 1.5” and 1.2” groups respectively showing it didn’t like the same thing the SPS did. My best for the day with the Model Seven came with Varget where both loads gave five shot groups of 1.2” and four shot groups of only 0.8”. That really is pretty much as good as I’ve gotten from that rifle so far as I recall. I think I had one load that turned in about the 0.75” to 0.80” size groups that I took to the PD shoot this year but due to limited shooting with it before going I can’t say if it can or can’t do better yet.

Varget turned in the second best performance from the SPS followed by AA2230 and W748 surprisingly to me came in dead last in the SPS with groups of 1.4” and 1.45” with the two loads tried. I’m sure some development work can do better as in the past some of my all time best .223 loads have come with W748 powder with both 40 and 50 grain bullets.

I will update this review from time to time as I do more load development with the MSS Varmint Nightmare bullets. I still a supply of them in both 50 and 55 grain weights in .224” plus an unopened box of the .172” 20 grain to work with in my .17 Fireball.

For now I can say that if you give them a try I’m sure you’ll be pleased with their performance and more than pleased with their price.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline JoeG52

  • Trade Count: (3)
  • Contributor
  • ***
  • Posts: 272
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #1 on: October 10, 2009, 12:44:48 AM »
Hey Bill, I think I may give some of these a try. Is there a way that GBO gets ‘credit’ for referring the purchase, like clicking a link from here? I would like Midsouth to know that sponsoring GBO has helped their sales.


Online Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26905
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #2 on: October 10, 2009, 12:50:12 AM »
Well if you go to their site by clicking a link from here they should be aware of it. You can just tell the person taking your order if you call the order in but if you do it online I guess only clicking their banner or a link to them from here would let them know. I added a link to them in the OP and here it is again.

www.midsouthshooterssupply.com


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline LHitchcox

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 211
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #3 on: October 10, 2009, 03:41:47 AM »
I have great respect for the folks at Midsouth. I have been doing business with them since the early 80s when they were located in East Tennessee. The 55 grain varmint nightmares are what my son shoots out of his 2 ARs. They are cheap enough to plink with and accurate enough for serious varminting. They are Hornadys by the look. BTW for just a few more pennies you can get the first quality Hornadys in a 250 pack under Hornady bulk bullets from the drop down menu on .224 bullets. Supposedly the varmint nightmares are seconds, but you will not know that from shooting them.

Some folks report mediocre accuracy with the 50 grain extremes which appear to be Sierras. I am well satisfied with the 55s, so I just plan to stay with them..

Online Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26905
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #4 on: October 10, 2009, 11:20:13 AM »
Quote
Supposedly the varmint nightmares are seconds, but you will not know that from shooting them.

Dunno about that as all I've seen so far (three boxes of 500 each) are bright and shiny and for sure not what's normally sold as seconds which is for appearance only.

Quote
Some folks report mediocre accuracy with the 50 grain extremes which appear to be Sierras. I am well satisfied with the 55s, so I just plan to stay with them..

Maybe but the ones I've loaded so far have proven some of the most accurate bullets for my .22-250 and I'd not call half inch groups at 100 yards mediocre accuracy.

I honestly don't know who makes them and they aren't likely to share that info. I've loaded up ten more rounds each at 24.0, 24.5, 25.0 and 25.5 grains of AA2460 as the 24.0 and 25.0 loads were most accurate of the previous batch. Next range session I'll shoot all 40 slowly thru the SPS Varmint to avoid mirage problems and see which that rifle prefers. I suspect one of them will prove to be a half MOA or better load in that rifle.


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Online Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26905
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #5 on: November 03, 2009, 01:15:20 PM »
First follow up on review:
I did some more shooting for this review today (11-03-09)

Using the Rem 700 SPS Varmint .223 I shot a group with the MSS 55 grain bullet over 25.5 grains of AA2460. I had a flyer that opened group to 0.9” but the other four went into a tight cluster measuring only 0.276”. Flyers were a common thread in my shooting today for some reason. I think that reason was the shooter.

It was the only group fired today with this rifle that I think was valid. It obviously has become fouled and accuracy has degraded badly from last shooting session. I’m going to clean the barrel and shoot these loads again as I just don’t think today’s results other than this one were indicative of what the loads are capable of. I’ve lost count of the rounds fired since last cleaning on this rifle and it’s just not fair to report specifics until I clean it and see if it repeats the good or the less good results of today.

Below is the one group I’m reporting on today.





Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline mjbgalt

  • Trade Count: (26)
  • Senior Member
  • *****
  • Posts: 2367
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #6 on: December 01, 2009, 01:45:40 PM »
that's what my groups with Varget and H4350 look like too. great bullets!
I have it on good authority that the telepromter is writing a stern letter.

Offline mjbgalt

  • Trade Count: (26)
  • Senior Member
  • *****
  • Posts: 2367
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #7 on: February 06, 2010, 01:29:02 PM »
shot the first 5 shot 1/2 inch group in my life with these bullets. i am ordering more!
I have it on good authority that the telepromter is writing a stern letter.

Offline LaOtto222

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3828
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #8 on: February 11, 2010, 06:14:34 AM »
I have shot both the 34 grain .224 and 50 grain .224 bullets. In a Handi that is a re-barreled (Douglas stub) 22K Hornet I got these groups using the 34 grain Mid South bullet. The Handi platform is not the best for accuracy - These bullets would do even better with a good bolt gun. Of course this is plenty accurate enough for it's range and it's intended use. Loads are listed on the target. I have shot them some in a Savage Model 40, but haven't done so enough to see if they are going to work out... I need to do more load development - but they look promising. BTW I got 500 to start with and then ordered 1000 more - can't beat the price and they shoot good too.





I have used the 50 grain nightmares in a Remington 700 that I re-barreled myself to 221 Fireball. I do not have any pictures of groups with it, but it will make 1 hole groups at 100 yards real consistently. They make the above groups look bad. Once in a while I get a flier that opens the group up to .5 -.6, but I blame that on me, not the bullet. I use RL7 and Remington 7 1/2 primers. I have shot a few

I have also used this bullet in a 23" T/C 221FB barrel. I consistently get groups under .75" with it and once in a while I will get a .5" group with it. I use a lighter load of RL7 for this gun. I have shot a few woodchucks with this gun/bullet (it is so easy to carry). I find that at 221 velocities (2900 fps muzzle); that I get a pass through. I have never lost a 'chuck due to this. The entry hole is a normal entry hole the exit is about the size of a nickle when shot 75- 100 yards. Some times I get an exit hole and some times not; if shot under 50 yards. 

I have not done any testing with the 50 grain bullets in my other guns - yet (a couple of 223s, and a 22 BR). I will be getting around to it this spring. I bought 1000 of these to start with (because of price) and liked them so well I got another 500 so my supply is back up over 1K.

Great men have vision and resolve to make dreams come true.

Offline hornady

  • Trade Count: (2)
  • Contributor
  • ***
  • Posts: 477
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #9 on: June 22, 2010, 03:16:42 AM »
I think they are the same bullet, but I have bought the Hornady Bulk & Breakdown 55gr, w/cann (250) bullets for $20.11 from Mid-South and I shoot them in My Savage model 11 in  223, and my Savage Stevens 200 in 22-250, and was very pleased with the results I got with a mid-range Hornady load of Varget.

Offline Catfish

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2696
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #10 on: August 14, 2011, 01:07:56 PM »
The 55 gr Varmint Nite Mare is my bullet of choice for coyote. It is to soft to be the ultiment bullet for terminal preformance, but nearly all of the coyotes I shoot at are running and I don`t want to shoot a bullet that will rickochet a long way, and probily 70% of the hits, the bullet does not exit the coyote. Their accuracy has been real good in everything I`ve shot them in.

Offline ratdog

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1000
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #11 on: April 26, 2012, 07:47:45 PM »
just bought some 55 grners  it will be a while till i get them. good price ;D

Offline Talltexanrancher

  • Trade Count: (0)
  • Member
  • *
  • Posts: 8
  • Gender: Male
Re: Midsouth Shooters Supply Varmint Nightmare Bullet Review
« Reply #12 on: April 19, 2013, 10:05:01 AM »
Guys,


While I'm very late to this conversation, I did want to mention that several years ago I bought 500 rounds of 55 grain Varmint Nightmare bullets for loading from MidSouth (they came in 100 count plastic pouches) because the price was right.  Problem was, it turns out after weighing a few before loading that they were all 60 grain in weight, not the 55 grain as advertised and as indicated by its sticker.  While not a huge deal, someone might be able to get in trouble loading max+ 223 loads in a Contender.  Once again, it shows that it always pays to weigh a bullet or two out of each box of bullets you intend to reload just to be safe.  By the way, they shot great and were just as accurate as the Nosler BTs that I typically loaded, but way cheaper.
Jeff