« previous next »
Pages: [1]   Go Down

Author Topic: Removing a screw  (Read 646 times)

0 Members and 3 Guests are viewing this topic.

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Removing a screw
« on: November 24, 2009, 05:16:29 AM »
I have a Norinco 1911 pistol.
I have new slim grips I want to install.
I have new stud/sleeves for the fame but cannot remove them.
I have tapped the but have not applied heat.
Good screwdrivers and vice grips don't work.
Blessings
Logged
TEXAS, by GOD

Offline madcratebuilder

  • Trade Count: (0)
  • Member
  • *
  • Posts: 95
Re: Removing a screw
« Reply #1 on: November 24, 2009, 06:35:31 AM »
May have loc-tite on them, heat it up with the tip of a soldering iron.
Logged

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: Removing a screw
« Reply #2 on: November 24, 2009, 07:18:51 AM »
Would a hair dryer suffice?
Blessings
Logged
TEXAS, by GOD

Offline SHOOTALL

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 23836
Re: Removing a screw
« Reply #3 on: November 24, 2009, 07:19:21 AM »
Kroil it and tap screw driver while trying to turn it . Yep need a vise or third hand .
Logged
If ya can see it ya can hit it !

Offline P.A. Myers

  • GBO Supporter
  • Trade Count: (65)
  • Senior Member
  • *****
  • Posts: 1344
Re: Removing a screw
« Reply #4 on: November 24, 2009, 07:57:53 AM »
I believe red loctite needs 450'F. Hairdryer not enough. A clean soldering tip is a good idea, should work.
Logged
“Never give in, never give in, never; never; never; never - in nothing, great or small, large or petty -
never give in except to convictions of honor and good sense”
 Winston Churchill

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: Removing a screw
« Reply #5 on: November 24, 2009, 08:47:11 AM »
Got one out---stripped one out.
That is tha way the day has gone.
Thanks too you boys for your help.
Blessings
Logged
TEXAS, by GOD

Offline rebel49

  • Trade Count: (0)
  • Member
  • *
  • Posts: 40
Re: Removing a screw
« Reply #6 on: November 24, 2009, 05:51:45 PM »
If you are talking about the grip screw bushings they are threaded AND staked in from the back side. Odds are you will end up stripping them all. Brownells has an oversize tap and oversize bushings to replace stripped frame holes. If they are locktited in you can free them up with a cheap pencil torch held right on the base of the bushing and a good hollowground screwdriver. When I replace the bushing I use red locktite and let it cure overnight. grip screws can be held in place real well by using real small "O" rings under them, been doing that for years and never had one come loose again since I started doing that.
Rebel49
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: Removing a screw
« Reply #7 on: November 24, 2009, 07:28:36 PM »
When removing grip screw bushings that are staked in, it is wise to cut out the stake first. It can usually be seen thru the cutouts in the frame from the side oposite the affending bushing. A mototool will work if used carefully.
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: Removing a screw
« Reply #8 on: November 25, 2009, 11:58:25 PM »
There are concerns with this Norinco that are above my abilities.
The steel of the Norinco is harder than American steel--it is not brittle though.
I am going to take it too Vandenbergs and let him do it before I really Bugger up this piece.
Blessings
Logged
TEXAS, by GOD
Pages: [1]   Go Up
« previous next »