Author Topic: New "WHITE" Barrel  (Read 637 times)

0 Members and 1 Guest are viewing this topic.

Offline FW Conch

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 404
  • Gender: Male
New "WHITE" Barrel
« on: December 02, 2009, 05:34:25 AM »
 :) I just  received a 260 REM barrel for my Stevens 200 in "white" & want to finish it myself.  I don't have access to an oven big enough to bake a 26" barrel, so I won't be doing that.

Can I get some suggestions on how to go with it - blue, something from Brownells, ? ? ?

Thanks in advance  :) :D ;D    Jim
Jim

Offline ncsurveyor

  • Trade Count: (24)
  • A Real Regular
  • ****
  • Posts: 821
Re: New "WHITE" Barrel
« Reply #1 on: December 02, 2009, 05:47:47 AM »
do you have access to a bead blaster and auto paint system?

Duracoat supposed to be "da bomb"

Offline FW Conch

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 404
  • Gender: Male
Re: New "WHITE" Barrel
« Reply #2 on: December 03, 2009, 03:21:13 AM »
 :( No I don't nc, that method is to far over the top for this project @ this time.  Others I know have

agreed that it is an excellent method.  Thanks for the suggestion.  :) Jim
Jim

Offline ncsurveyor

  • Trade Count: (24)
  • A Real Regular
  • ****
  • Posts: 821
Re: New "WHITE" Barrel
« Reply #3 on: December 03, 2009, 03:28:22 AM »
In that case, you can build an "oven" for baked on finishes.  Find a larger diameter metal pipe and some space heaters.

Use a brass cleaning rod to run through the barrel, then suspend you're barrel using other wires tied off at the ends of your "oven".

Two ceramic space heaters, one on each end, should get the heat up enough to do it OK.  Optionally, a bigger one aimed at the pipe will do also, and likely provide convection.

Let me know and I can draw a pic.  The one I used is long since been converted to something else.

Cold blue just doesn't work for me.

Offline FW Conch

  • GBO Supporter
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 404
  • Gender: Male
Re: New "WHITE" Barrel
« Reply #4 on: December 03, 2009, 06:25:54 AM »
  :) Now that I could do !  Thanks nc , & your discripton was quite adequate so a picture won't be necessary.  Good Shooting !  Jim   :) ;D
Jim

Offline ncsurveyor

  • Trade Count: (24)
  • A Real Regular
  • ****
  • Posts: 821
Re: New "WHITE" Barrel
« Reply #5 on: December 03, 2009, 06:32:25 AM »
IIRC the instructions indicated a 300degree temp, and with the heaters I used, butted right up to the ends of the pipe, I think I achieved 220, but I let it go about 4 hourse (outside in a clear area of an outbuilding).  Just make sure you're safe, fire hazard wise.

I also used the same tube and set it on the gas grill once to do another barrel.   :D

That one I'm pretty sure got above 300.  I should have grilled a few burgers while it was going, though.

Offline ncsurveyor

  • Trade Count: (24)
  • A Real Regular
  • ****
  • Posts: 821
Re: New "WHITE" Barrel
« Reply #6 on: December 03, 2009, 06:33:58 AM »
duplicate