« previous next »
Pages: [1]   Go Down

Author Topic: Help,I need some info with this omega BDC250  (Read 622 times)

0 Members and 1 Guest are viewing this topic.

Offline deerslayer79

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 122
  • Gender: Male
Help,I need some info with this omega BDC250
« on: December 20, 2009, 09:04:50 AM »
I just got one for my omega,and doesn't group very good with the recommended load,the gun shoots bug hole groups with the original load I had of 2,50gr-777pellets and a L-N-L 250gr hornady,just got the scope and wondered if any of you guys out there using the same or close to load and what ranges are the are the circles are on at?
Logged
beer,check ammo,check gun,DAMMIT,I knew I forgot somethin!!

Offline Redhawk1

  • Life time NRA Supporter.
  • GBO Supporter
  • Trade Count: (78)
  • Senior Member
  • *****
  • Posts: 10748
  • Gender: Male
Re: Help,I need some info with this omega BDC250
« Reply #1 on: December 20, 2009, 10:59:15 AM »
I did well with 120 gr. loose triple 7 and T/C Bonded Shockwaves 250 gr. The 100 cross hairs, and the 150 and 200 yard circles worked as advertised.
Logged
If  you're going to make a hole, make it a big one.
ΜΟΛΩΝ ΛΑΒΕ
Only two defining forces have ever offered to die for you,
Jesus Christ and the American G. I.
One died for your soul, the other for your freedom

Endowment Life Member of the NRA
Life Member NA

Offline mirage1988

  • GBO Supporter
  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 1665
Re: Help,I need some info with this omega BDC250
« Reply #2 on: December 20, 2009, 11:56:12 AM »
I would get rid of the L-N-L sabots, or at least clip off the tail, the hole in the middle of the pellets is there so both pellets ignite at the same time. Sorry to derail your thread about the BDC, I don't have one.
Logged

Offline Urban_Redneck

  • Trade Count: (0)
  • Posts: 4
Re: Help,I need some info with this omega BDC250
« Reply #3 on: December 21, 2009, 04:40:22 AM »
Don't let the tail wag the dog... If you have a load that shoots/works well for you, zero the rifle and shoot to find where the circles intersect the trajectory. Write down the results and tape them to your stock.

Just my $0.02
Logged

Offline Jim47

  • Trade Count: (0)
  • Member
  • *
  • Posts: 14
Re: Help,I need some info with this omega BDC250
« Reply #4 on: December 21, 2009, 01:06:14 PM »
I have the same rifle and scope, but I haven't had time yet to test it in that way. But I also would suggest using a differnt bullet and maybe even swicthing to plain Pyrodex. There isn't anything that will shoot more consistant and for the most part with less trouble. Some guys like the new Blackhorn209 which I've heard is a lot cleaner, but may also present some ignition problems with certain primers. I use HornadayXTP's and like them.
Logged

Offline deerslayer79

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 122
  • Gender: Male
Re: Help,I need some info with this omega BDC250
« Reply #5 on: December 21, 2009, 01:44:09 PM »
thanks for the info guys any and all will be greatly appriciated
Logged
beer,check ammo,check gun,DAMMIT,I knew I forgot somethin!!

Offline zr800o1le

  • Trade Count: (12)
  • Avid Poster
  • **
  • Posts: 124
  • Gender: Male
Re: Help,I need some info with this omega BDC250
« Reply #6 on: December 21, 2009, 04:49:19 PM »
Thompson Set the Specs using 3 777's for a 150 grains and 250 gr. T/C Shockwave Sabots.
The Circles are Zero at 100, Then 150,200,225,250 
I also just found this site, http://www.nikonusa.com/fileuploads/pdfs/OMEGA_manual.pdf
 WOW. Very Interesting for Zeroing in with Spec loads, AND With Different Grain Loads.
Good Luck.     
Logged
Pages: [1]   Go Up
« previous next »