« previous next »
Pages: [1]   Go Down

Author Topic: Single Shot wobble  (Read 1584 times)

0 Members and 1 Guest are viewing this topic.

Offline 277284

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 144
Single Shot wobble
« on: December 31, 2009, 07:10:37 PM »
I'm checking out the Rossi single shot rifle in 357 mag.  Should i be concerned about the side to side wobble of the reciever/barrel in both locked up and in open breech position?  The two brand new Rossi rifles I have seen both do this.  Thanks
Logged

Offline Spanky

  • Moderators
  • Trade Count: (96)
  • Senior Member
  • *****
  • Posts: 4627
  • Gender: Male
  • USMC Semper Fidelis
Re: Single Shot wobble
« Reply #1 on: January 01, 2010, 05:48:59 AM »
If it is loose with it closed you need to shim the barrel at the underlug to tighten it up.
It's not really a big deal when it's opened, it's more of an annoyance. Does the gun have wood or synthetic stocks on it?
Check out the FAQ's link in the H&R centerfire section. There is a section on barrel fitting for the novice. Some very good info. that will help you.



Spanky
Logged

Offline 277284

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 144
Re: Single Shot wobble
« Reply #2 on: January 01, 2010, 11:03:05 AM »
They are wood, just handling both at different sporting goods stores.
Logged

Offline trotterlg

  • GBO Supporter
  • Trade Count: (36)
  • Senior Member
  • *****
  • Posts: 3978
  • Gender: Male
Re: Single Shot wobble
« Reply #3 on: January 01, 2010, 11:24:31 AM »
Like Sapnky said, it is normal to have play in it when opened, it is not proper to have any play in it when it is closed.  Larry
Logged
A gun is just like a parachute, if you ever really need one, nothing else will do.

Offline 277284

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 144
Re: Single Shot wobble
« Reply #4 on: January 01, 2010, 02:39:15 PM »
Thanks guys, the two I handled I was able to twist and move when locked up.  When in open position very loose on both.
Logged

Offline Deerhunter#1

  • GBO Supporter
  • Trade Count: (84)
  • Senior Member
  • *****
  • Posts: 1047
Re: Single Shot wobble
« Reply #5 on: June 13, 2010, 10:26:26 AM »
Got on in 22-250 that was loose. If you remove the forend you will find a metal cap that is crewed to it. Take the one screw out and place a small piece of shim material such as rubber and then screw it back on. It puts pressure against the forend and receiver and will tighten it up. Dont know if the fit off the forend was bad from the manufacturing or due to the wood it may swell and contract with weather change but the rubber should be able to flex with those changes. Mine has worked fine since.
Logged

Offline mrussel

  • Trade Count: (2)
  • A Real Regular
  • ****
  • Posts: 838
Re: Single Shot wobble
« Reply #6 on: June 19, 2010, 08:23:57 PM »
Quote from: Deerhunter#1 on June 13, 2010, 10:26:26 AM
Got on in 22-250 that was loose. If you remove the forend you will find a metal cap that is crewed to it. Take the one screw out and place a small piece of shim material such as rubber and then screw it back on. It puts pressure against the forend and receiver and will tighten it up. Dont know if the fit off the forend was bad from the manufacturing or due to the wood it may swell and contract with weather change but the rubber should be able to flex with those changes. Mine has worked fine since.

 From my reading of the OP it sounds like these were brand new at sporting goods stores. I wouldn't buy something new that I had to end up fixing with a shim.
Logged
Pages: [1]   Go Up
« previous next »