« previous next »
Pages: [1]   Go Down

Author Topic: 357 max reaming  (Read 687 times)

0 Members and 1 Guest are viewing this topic.

Offline yukondog

  • GBO Supporter
  • Trade Count: (43)
  • Senior Member
  • *****
  • Posts: 1095
357 max reaming
« on: January 01, 2010, 05:43:44 PM »
As soon as the reamer gets here I'll be taking the 357 max. ream plunge, any advice, I know to take the ejector out and use plenty of cutting oil and clean offten.Any advice would be a big help,thanks in advance.
Logged
an unloaded wepon is equal to the same mass and volume as a rock.

Offline krod47nw

  • GBO Supporter
  • Trade Count: (250)
  • Senior Member
  • *****
  • Posts: 1133
  • Gender: Male
Re: 357 max reaming
« Reply #1 on: January 01, 2010, 05:58:05 PM »
Just let the reamer do the cutting.  Don't put any pressure on it at all.  I found that if you put the barrel in a vise in the vertical position it works good.  this way the reamer is going straight all the time. Put some black marker or something on the rim cut so you can tell when the reamer touches it.

Kevin
Logged
The beauty of the Second Amendment is that it will not be needed until they try to take it.  Thomas Jefferson

Offline Swampman

  • GBO Supporter
  • Trade Count: (44)
  • Senior Member
  • *****
  • Posts: 16518
  • Gender: Male
Re: 357 max reaming
« Reply #2 on: January 01, 2010, 06:02:31 PM »
I didn't take my ejector out.
Logged
"Brother, you say there is but one way to worship and serve the Great Spirit. If there is but one religion, why do you white people differ so much about it? Why not all agreed, as you can all read the Book?" Sogoyewapha, "Red Jacket" - Senaca

1st Special Operations Wing 1975-1983
919th Special Operations Wing  1983-1985 1993-1994

"Manus haec inimica tyrannis / Ense petit placidam sub libertate quietem" ~Algernon Sidney~

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: 357 max reaming
« Reply #3 on: January 01, 2010, 09:03:05 PM »
From the reamer rental sticky...

Quote from: quickdtoo on October 06, 2009, 05:39:14 AM
Just PM me for the 357max reamer, I don't have a video cam to do one,  but I don't really think a video is necessary, it's just too simple.  ;) There are good instructions in the FAQs, just never turn the reamer backwards, always turn it clockwise in the cutting direction and use lots of cutting oil, it doesn't hurt to remove the reamer every few turns to clean the cuttings off, and go slow keeping the reamer inline with the bore, mounted vertical in a bench vice is the easiest way to do that, don't use the ends of the reamer handle for torque, try to turn it from as near the center as possible, the last two I did I used a nut driver and a 3/8" square drive socket so I'm just twisting the reamer and I'm less likely to end up cutting an egg shaped chamber by too much side force.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline cwlongshot

  • GBO Supporter
  • Trade Count: (158)
  • Senior Member
  • *****
  • Posts: 9907
  • Gender: Male
  • Shooting, Hunting, the Outdoors & ATVs
Re: 357 max reaming
« Reply #4 on: January 02, 2010, 02:04:25 AM »
Like Tims quote says, be very consious of side to side pressure. Its pretty easy to egg shap a chamber with the longer reamers. The deeper they are the easier this is to do. its not hard to do, the whole thing will likely be done in 10 minutes!! I didn't have to do a maxi as mine was factory chambered, but I have done a couple others.
 I make one complete turn, removed the reamer, blew out the chamber and the reamer, oiled the reamer and repeat. Just GO SLOWLY. You will be a master in no time!!!

CW
Logged
"Pay heed to the man who carries a single shot rifle, he likely knows how to use it."

NRA LIFE Member 
Remember... Four boxes keep us free: the soap box, the ballot box, the jury box, and the cartridge box.

Offline yukondog

  • GBO Supporter
  • Trade Count: (43)
  • Senior Member
  • *****
  • Posts: 1095
Re: 357 max reaming
« Reply #5 on: January 02, 2010, 03:20:45 AM »
Thanks for the tips,the nut driver idea is the way to go I think.
Logged
an unloaded wepon is equal to the same mass and volume as a rock.

Offline Swampman

  • GBO Supporter
  • Trade Count: (44)
  • Senior Member
  • *****
  • Posts: 16518
  • Gender: Male
Re: 357 max reaming
« Reply #6 on: January 02, 2010, 04:06:00 AM »
It seems scary at first but it's a cake walk.  I only cleaned the reamer every 3 turns and I used an air nozzle to blow the chips out of the barrel.  Go slow and use lots of oil.
Logged
"Brother, you say there is but one way to worship and serve the Great Spirit. If there is but one religion, why do you white people differ so much about it? Why not all agreed, as you can all read the Book?" Sogoyewapha, "Red Jacket" - Senaca

1st Special Operations Wing 1975-1983
919th Special Operations Wing  1983-1985 1993-1994

"Manus haec inimica tyrannis / Ense petit placidam sub libertate quietem" ~Algernon Sidney~

Offline Badnews Bob

  • Trade Count: (34)
  • Senior Member
  • *****
  • Posts: 2963
  • Gender: Male
Re: 357 max reaming
« Reply #7 on: January 02, 2010, 04:10:33 AM »
Peice of cake the reamer I used (DJs the one that got passed around several years ago) didn't have  the rim cutter built in all you had to do was turn it till the rim bottomed out zip your done no chance of cutting to deep. I really like that rifle, It will be one of the last I ever let go. 8)
Logged
Badnews Bob
AE-2 USN retired
Pages: [1]   Go Up
« previous next »