« previous next »
Pages: [1]   Go Down

Author Topic: New lead melter  (Read 2047 times)

0 Members and 2 Guests are viewing this topic.

Offline Eyes Of Death

  • Trade Count: (0)
  • Member
  • *
  • Posts: 89
  • Gender: Male
    • Dehogger
New lead melter
« on: February 06, 2010, 04:25:16 PM »
Decided to try out the new lead melter I built. It's not finished but had to try it out. Made some ammo for my cannon 1# balls. I used wheel weights. The kiln will hold 150# at least of lead. It's bottom pore uses tapered plug in the bottom works great.



Made 50 balls in hour and half. Golf ball size
Logged

Offline Eyes Of Death

  • Trade Count: (0)
  • Member
  • *
  • Posts: 89
  • Gender: Male
    • Dehogger
Re: New lead melter
« Reply #1 on: February 06, 2010, 04:25:47 PM »


I think my pin would float up if I get it full of lead. I will have to add a spring.
Logged

Offline GGaskill

  • Moderator
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 5668
  • Gender: Male
Re: New lead melter
« Reply #2 on: February 06, 2010, 04:35:01 PM »
I will have to add a spring.

Or a weight to the end of the handle.

Have you cut any of the balls in half to see if there is a void inside?  Heats with propane?
Logged
GG
“If you're not a liberal at 20, you have no heart; if you're not a conservative at 40, you have no brain.”--Winston Churchill

Offline BoomLover

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1152
  • Gender: Male
Re: New lead melter
« Reply #3 on: February 06, 2010, 06:30:46 PM »
Pretty good set-up! Sometimes homemade is better than store bought!
Logged
"Beware the Enemy With-in, for these are perilous times! Those who promise to protect and defend our Constitution, but do neither, should be evicted from public office in disgrace!

Offline Double D

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 12609
  • SAMCC cannon by Brooks-USA
    • South African Miniature Cannon Club
Re: New lead melter
« Reply #4 on: February 06, 2010, 06:34:09 PM »
Have you shot lead balls this size before out of you cannon? Pressure and reduced loads?
Logged

Offline KABAR2

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 2830
Re: New lead melter
« Reply #5 on: February 06, 2010, 11:09:53 PM »
That's a lot of lead to heat up in that beast!  I think when summer rolls around

you'll be needing one of those asbestos suites to get close enough to do any casting........

Logged
Mr president I do not cling to either my gun or my Bible.... my gun is holstered on my side so I may carry my Bible and quote from it!

Sed tamen sal petrae LURO VOPO CAN UTRIET sulphuris; et sic facies tonituum et coruscationem si scias artficium

Offline dan610324

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2413
  • Gender: Male
  • bronze cannons and copper stills ;-))
    • dont have
Re: New lead melter
« Reply #6 on: February 06, 2010, 11:19:19 PM »
or even better , put a 2" rockwool insulation on the outside
that will also do that your melting pot will use less propane
Logged
Dan Pettersson
a swedish cannon maniac
interested in early bronze guns

better safe than sorry

Offline Eyes Of Death

  • Trade Count: (0)
  • Member
  • *
  • Posts: 89
  • Gender: Male
    • Dehogger
Re: New lead melter
« Reply #7 on: February 07, 2010, 03:08:43 AM »
I'm in the process of ordering some ceramic fiber blankets for another job and was going to order an extra one. The blankets come wet and you mold them to your needs. And then heat up the item and then the blankets set in place. When I break off the feed tube, if theirs air it shows up there and I just toss it back in the meter. Is the feed tube called a punt?
Logged

Offline Cat Whisperer

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 7493
  • Gender: Male
  • Pulaski Coehorn Works
Re: New lead melter
« Reply #8 on: February 07, 2010, 03:14:57 AM »
EOD -

How much of a taper on the valve?  I'd love to see the details.

I'd like to build one for doing both cannon balls and ingots for bullet casting.
Logged
Tim K                 www.GBOCANNONS.COM
Cat Whisperer
Chief of Smoke, Pulaski Coehorn Works & Winery
U.S.Army Retired
N 37.05224  W 80.78133 (front door +/- 15 feet)

Offline Eyes Of Death

  • Trade Count: (0)
  • Member
  • *
  • Posts: 89
  • Gender: Male
    • Dehogger
Re: New lead melter
« Reply #9 on: February 07, 2010, 03:37:14 AM »
To tell you the truth I don't know the proper taper dimensions. I just happened to have a tapered reamer in a bunch of stuff in a box and the numbers are rubbed off. I did have the cross slide on my lathe set just past 3 deg. I made the female parts first. Then used black permanent ink on the mail to see the points of contact. And made an adjust mint tell there was even wear. The plug is water tight.
Logged

Offline Cat Whisperer

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 7493
  • Gender: Male
  • Pulaski Coehorn Works
Re: New lead melter
« Reply #10 on: February 07, 2010, 03:38:43 AM »
Great !   That's all I need to know to make one!
Logged
Tim K                 www.GBOCANNONS.COM
Cat Whisperer
Chief of Smoke, Pulaski Coehorn Works & Winery
U.S.Army Retired
N 37.05224  W 80.78133 (front door +/- 15 feet)

Offline RocklockI

  • GBO Supporter
  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 2747
  • Gender: Male
  • Morko and Me
Re: New lead melter
« Reply #11 on: February 07, 2010, 05:15:00 AM »
It's cool alright , But having been around hot metal ,it looks kinda shaky to me/top heavy . Unless it welded to the table ......
Logged
"I've seen too much not to stay in touch , With a world full of love and luck, I got a big suspicion 'bout ammunition I never forget to duck" J.B.

Offline Terry C.

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1215
  • Gender: Male
  • I see what you did there...
Re: New lead melter
« Reply #12 on: February 07, 2010, 05:41:18 AM »
Can't really tell in the small photo, but it does look like the legs are tack welded to the plate.
Logged

Offline Eyes Of Death

  • Trade Count: (0)
  • Member
  • *
  • Posts: 89
  • Gender: Male
    • Dehogger
Re: New lead melter
« Reply #13 on: February 07, 2010, 02:11:50 PM »
It is tack welded to the tabel, to easy not to.
Logged

Offline 1Southpaw

  • GBO Supporter
  • Trade Count: (0)
  • A Real Regular
  • *****
  • Posts: 642
  • Gender: Male
  • Let Freedom ring
Re: New lead melter
« Reply #14 on: February 08, 2010, 03:19:31 AM »
Fine project , Looks good to these old eyes , and .... I finally found a shop that looks like mine !    ::)
The table top it's tacked to looks substantial enough to hold the "super pot"  ;D
Logged
Left Handed people are in their right mind .
Pages: [1]   Go Up
« previous next »