« previous next »
Pages: [1]   Go Down

Author Topic: Ithaca/SKB 200E 20ga  (Read 2769 times)

0 Members and 1 Guest are viewing this topic.

Offline all4abuck

  • Trade Count: (0)
  • Member
  • *
  • Posts: 71
  • Gender: Male
Ithaca/SKB 200E 20ga
« on: February 28, 2010, 03:09:08 PM »
I go a 20ga sxs ithaca/SKB 200E shotgun from a family member.  I am not familiar with sxs guns as I have never owned one before.  The gun looks great and I like to take it out and try it.  However I noticed a rattle when I was handling it.  I can hear something like a screw or spring lose in the stock side of the action when I shake the gun.  Seems to be rolling around in there.  Took the butt plate apart and nothing in the stock.  Looks like it is in the box action/trigger assembly.

Any idea what this could be?  I will take it to a gunsmith but just want to get an idea of what I should expect.

I took the 3 screws on the bottom of the receiver out but it doesn't seem to release the trigger assembly.  Is there a disassembly procedure or diagram out there that I can get for this gun?  Like to take it apart without screwing up anything.

Any help on this will be appreciated.
Logged
Blessed be the Lord my strength, which teacheth my hands to war, and my fingers to fight. My goodness, and my fortress; my high tower, and my deliverer; my shield, and he in whom I trust;

Offline Rangr44

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 2158
Re: Ithaca/SKB 200E 20ga
« Reply #1 on: March 01, 2010, 07:52:01 AM »
[ I am not familiar with sxs guns.]
[I took the 3 screws on the bottom of the receiver out but it doesn't seem to release the trigger assembly.]

That's exactly what NOT to do, and most likely the source of the rattle, when someone else before you tried the same thing - unless the safety spring's gone sprong.

Unless some has a lot of experience with SxS shotguns, the most that should be done is to pull the buttstock for a clean/flush/oil.

Please take it to a gunsmith.

.
Logged
There's a Place for All God's Creatures - Right Next to the Potatoes & Gravy ! !

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Re: Ithaca/SKB 200E 20ga
« Reply #2 on: March 01, 2010, 08:01:46 AM »
Don't have my book here but have to agree with ranger44. Removing screws with no knowlesge of what is released is NOT a great idea. With the buttstock off one should be able to see whats going on inside.. Regardless I'd lean toward invloving a good gunsmith in this problem. The SKB shotguns are well made but I've not had a lot of involvement with the SxS guns, mostly the OU varieties..
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline Dirt Bag

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 161
Re: Ithaca/SKB 200E 20ga
« Reply #3 on: March 01, 2010, 12:21:50 PM »
  We got into this one when we re stocked it .. Seems like I remember pins with "C clip" retainers on the ends of them, rather than being staked. Could be one of those rattling around in there.


   And yes, take it to a gunsmith.   Good luck.
                                                            D.B.       
Logged
Pages: [1]   Go Up
« previous next »