Author Topic: Metal Trigger Guard  (Read 4002 times)

0 Members and 1 Guest are viewing this topic.

Offline GreenMachine79

  • Trade Count: (8)
  • Member
  • *
  • Posts: 68
  • Gender: Male
    • Toth Tool & Engineering, LLC
Re: Metal Trigger Guard
« Reply #30 on: September 06, 2010, 02:47:22 PM »
It's been a long time since I updated this thread, I had the parts black oxided soon after my last post, but I've been to busy to play with the guns.  Here are the results, I stopped short of pushing the pins in all the way because I have yet to do a trigger job on the rifle. 





Offline Lon371

  • GBO Supporter
  • Trade Count: (53)
  • Senior Member
  • *****
  • Posts: 2486
  • Gender: Male
  • Why Not a Handi?
Re: Metal Trigger Guard
« Reply #31 on: September 06, 2010, 03:06:35 PM »
  Very nice!   You will have several people slobbering now :D

Lonny

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Metal Trigger Guard
« Reply #32 on: September 06, 2010, 03:15:08 PM »
WOW, very nice!  :o :o
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.


Offline AtlLaw

  • Moderators
  • Trade Count: (58)
  • Senior Member
  • *****
  • Posts: 6405
  • Gender: Male
  • A good woman, nice bike and fine guns!
Re: Metal Trigger Guard
« Reply #33 on: September 06, 2010, 03:18:32 PM »
SLOBBER SLOBBER!   :P
Richard
Former Captain of Horse, keeper of the peace and interpreter of statute.  Currently a Gentleman of leisure.
Nemo me impune lacessit

                      
Support your local US Military Vets Motorcycle Club

Offline GreenMachine79

  • Trade Count: (8)
  • Member
  • *
  • Posts: 68
  • Gender: Male
    • Toth Tool & Engineering, LLC
Re: Metal Trigger Guard
« Reply #34 on: September 22, 2010, 07:30:01 PM »
Their was a few people following this thread as well as people interested in purchasing steel trigger guards. More information on the matter can be found here: http://www.gboreloaded.com/forums/index.php/topic,216464.0.html

Offline DCmauser

  • Trade Count: (0)
  • Member
  • *
  • Posts: 84
Re: Metal Trigger Guard
« Reply #35 on: September 23, 2010, 10:28:25 AM »
What finishing process are you using to remove the machine marks?  One grey photo appears to be sand-blasted or acid-dipped?  Would a rock-tubbler take away machining, round sharp corners or sharp points?

Offline GreenMachine79

  • Trade Count: (8)
  • Member
  • *
  • Posts: 68
  • Gender: Male
    • Toth Tool & Engineering, LLC
Re: Metal Trigger Guard
« Reply #36 on: September 23, 2010, 02:06:15 PM »
What finishing process are you using to remove the machine marks?  One grey photo appears to be sand-blasted or acid-dipped?  Would a rock-tubbler take away machining, round sharp corners or sharp points?

On these particular parts I tumbled them for a short period of time to remove small burrs and sand blasted to remove machine marks. Their are dozens of ways to deburr and remove machine marks as well as a vast combination of medias that can either be used wet or dry. Typically I will deburr by hand for large burrs, tumble for small burrs, and sand blast to remove machine marks as well as give a nice prep before bluing.

Offline D Humbarger

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 196
  • Gender: Male
Re: Metal Trigger Guard
« Reply #37 on: September 23, 2010, 03:52:18 PM »
Just put in my order.  ;D
Try to look unimportant.   Your enemy might be low on ammo.

Only Handi so far is a 375 JDJ.

Offline troy5775

  • Trade Count: (56)
  • Contributor
  • ***
  • Posts: 456
  • Gender: Male
Re: Metal Trigger Guard
« Reply #38 on: September 23, 2010, 06:45:11 PM »
I have seen a couple of others mention it, have you thought of doing any in brass?

Offline GreenMachine79

  • Trade Count: (8)
  • Member
  • *
  • Posts: 68
  • Gender: Male
    • Toth Tool & Engineering, LLC
Re: Metal Trigger Guard
« Reply #39 on: September 24, 2010, 06:56:31 AM »
I have seen a couple of others mention it, have you thought of doing any in brass?

After I make a batch of them out of steel I would be willing to do them out of brass if enough people are interested.