Author Topic: .410 Tamer came home with me (Read 1292 times)

BillinOregon · « **on:** June 05, 2010, 03:25:36 PM »

Couldn't resist any longer the siren song of this little .410. Hope to pattern it soon with 3-inch shot loads and some 2.5-inch No. 8 target loads, as well test the accuracy of Winchester slugs. I have high hopes, but may try to figure out some sort of simple rear sight to help with the slugs. Will also look at attaching a sling. The butt stock will be easy, but not so sure about the forend without maybe some JB Weld or something besides polymer for the screw to bite into.
Anyone with Tamer experience is welcome to chime in.
Bill

spruce · « **Reply #1 on:** June 06, 2010, 03:27:16 PM »

For the front sling mount I'd use a Uncle Mike's barrel band to attach it. Just measure the diameter of the barrel in the area you want to attach it and order the appropriate size.

I use them on several shotguns and rifles and never had a problem with them.

kynardsj · « **Reply #2 on:** June 06, 2010, 03:59:24 PM »

Had a Tamer some years ago. It was a snakes nightmare. Also owned a Snake Charmer but liked the Tamer better.

BillinOregon · « **Reply #3 on:** June 06, 2010, 05:08:23 PM »

Spruce: I have used the Uncle Mike's barrel band swivels with complete satisfaction as well. They're getting hard to find without ordering over the Net, though, so I was wondering about ways to attach a standard swivel to the forend.

gendoc · « **Reply #4 on:** June 20, 2010, 12:28:11 PM »

bill, we have several tamer stock sets on various handi calibers. 45/410, 17hm2, 22lr/410vp, 22mag/vp(rc) and a 20ga. my grandkids really like the tamer stocks.... and me too !!! .460/410 in reduced load .460 (my tractor blaster)

all of them have the same forend, if you look inside the forend about 3" in front of the forend screw hole
there is a plastic raised boss there... drill it out smaller than a sling stud screw and thread it in.
we have 2 like that. and it works real good. just don't drill the pilot hole too big.
i don't like attaching anything to the barrel. but, thats just me

i guess your forends are the same as the ones they have previously made in the past like ours...

i did change the forend on my tractor blaster to a new style checkered synthetic
and the 17hm2 forend to one of them ati tacticle forends. which don't have studs, but are stud ready if needed

we like the stocks !!!!

BillinOregon · « **Reply #5 on:** June 22, 2010, 05:39:21 AM »

Gendoc: Thanks for the tip!

Spanky · « **Reply #6 on:** June 22, 2010, 07:53:50 AM »

gendoc... will the shell holder in the stock hold the 460's? I'm thinkin' on gettin' one for my soon to be 444 and don't know if it'll hold the shells tight.

Spanky

gendoc · « **Reply #7 on:** June 22, 2010, 12:22:05 PM »

spank, you bet they will !!!

just open the hole jus a lil bit.... i did it with a drill bit chucked ina t-handle
wish i could remember what size it was. it don't need much !!
i did the bottom 2 and left the other 2 for the shotshell.
it works great

Spanky · « **Reply #8 on:** June 22, 2010, 01:19:57 PM »

Perfect... thanks buddy.

Spanky

gendoc · « **Reply #9 on:** June 22, 2010, 01:38:56 PM »

spanky i fergot to mention....as you prolly know, remove the screw dowel and o-rang 1st .
maybe others might try it too