« previous next »
Pages: [1]   Go Down

Author Topic: 35 Whelen and 200 gr. Bullets  (Read 532 times)

0 Members and 1 Guest are viewing this topic.

Offline Mckie Hollow

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 265
35 Whelen and 200 gr. Bullets
« on: June 26, 2010, 06:32:37 AM »
My new 700 CDL seems to have a very long leed. I can't begin to get close to the lans with a 200 gr. bullet. My question is this. How far out should I seat and still have a good safe hunting load? I was thinking no less than 1/2 the bullet diameter seating depth? When I made a dummy round with a Speer 250gr. and closed the bolt to seat the bullet. The bullet was barely seated and I could pull it apart with my fingers. I didn't bother to try to measure what depth the lans pushed the bullet to. It wasn't very much.
Logged

Offline Sweetwater

  • GBO Supporter
  • Trade Count: (17)
  • Senior Member
  • *****
  • Posts: 1286
  • Gender: Male
  • When it ceases to be fun, I shall cease to do it.
Re: 35 Whelen and 200 gr. Bullets
« Reply #1 on: June 26, 2010, 07:20:29 AM »
Maximum OAL is governed by your chamber, your magazine and your bullet. My 8x57mm gets .25" seating depth as that is where it feeds correctly and is still tight enough that I cannot pull the bullet with my fingers. I carry them in a pocket quite often and they still stay tight. My rifle is long throated and a flat base 200gr will "just kiss" the rifling and a boat-tail doesn't come close. A 225gr boat-tail will touch the rifling. Don't over think this "seat to the rifling" or other "sayings". Give your ammo the best fit to your rifle and make it happen.

I was going to say 1/2 caliber might make a good reference for seating depth, but then there are the smaller calibers and that wouldn't work at all. .15" seating depth might work for bench shooting (or even a little less) as these cartridges are handled gently as compared to thrasing around in the brush.
Logged
Regards,
Sweetwater

Courage is being scared to death but saddling up anyway - John Wayne

The proof is in the freezer - Sweetwater

Offline Siskiyou

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3417
  • Gender: Male
Re: 35 Whelen and 200 gr. Bullets
« Reply #2 on: June 26, 2010, 07:32:22 AM »
Congratulations on your CDL in 35 Whelen.  I have no real need for one, but that has been one of my dream combinations.  A few months ago I was looking for .35 caliber bullets for my brother and had little luck.  Looks like supplies have improved a little.
Logged
There is a learning process to effectively using a gps.  Do not throw your compass and map away!

Boycott: San Francisco, L.A., Oakland, and City of Sacramento, CA.

Offline stimpylu32

  • Moderators
  • Trade Count: (67)
  • Senior Member
  • *****
  • Posts: 6062
  • Gender: Male
Re: 35 Whelen and 200 gr. Bullets
« Reply #3 on: June 26, 2010, 10:57:29 AM »
MH

Start with the given COL for the bullet your using and work out from there to see what groups best , for my hunting loads I never have less than 1 full bullet dia. in the neck .

stimpy
Logged
Deceased June 17, 2015


:D If i can,t stop it with 6 it can,t be stopped

Offline mostlyaccurate

  • Trade Count: (0)
  • Member
  • *
  • Posts: 18
Re: 35 Whelen and 200 gr. Bullets
« Reply #4 on: June 26, 2010, 03:54:06 PM »
With 225 gr accubonds I'm having good luck with 2/3's bullet dia in the neck.  That's in a single shot with a long throat and no trouble so far.  As well with mine, still a long way from the lans.  Good luck & I love my Whelen.
Logged

Offline Mckie Hollow

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 265
Re: 35 Whelen and 200 gr. Bullets
« Reply #5 on: June 26, 2010, 05:13:54 PM »
Right now, I have 4 Rem. CL SP's seated @ 75 percent of bullet diam. . I'm going to try this. The gun took a turn for the better, last weekend. It filled the bull @ 75 yds.. It would not do this, initially. Accuracy has vastly improved. Due to breaking in, bedding / free floating, working on a load.
Logged

Offline Dinny

  • Moderators
  • Trade Count: (268)
  • Senior Member
  • *****
  • Posts: 5524
  • Gender: Male
  • "Medics Save"
Re: 35 Whelen and 200 gr. Bullets
« Reply #6 on: June 26, 2010, 05:34:15 PM »
FWIW, I have a couple of other things to consider.... Barnes, solid-copper, bullets are longer and may fit your needs better, as long as you can still fit them in the magazine. Another thought is crimping your bullets. Some folks do and some do not. For hunting loads, I do. That helps to assure me that the bullets are less likely to move or become free.

Thanks, Dinny


Logged
Handi Family: 357 Max, 45 LC, 45-70, 300 BLK, 50 cal Huntsman, and 348 Win.

"If there must be trouble, let it be in my day that my child may have peace"
Thomas Paine

Offline Ole Man Dan

  • Trade Count: (0)
  • Member
  • *
  • Posts: 92
  • Gender: Male
Re: 35 Whelen and 200 gr. Bullets
« Reply #7 on: June 29, 2010, 08:24:57 PM »
I've loaded hundreds of 200 gr. Remington's in several Whelen's and they were a 'real stopper' on deer.
I load 250 gr. Speer's for animals larger than Deer.

Years ago when I began loading for the Whelen's; I adjusted my equipment to a Remington factory 200 Gr.
I did the same for the 250 gr. bullets.
I've since adjusted my loads for the individual rifles. (Ruger, Remington, or Interarms actions)
Logged
Pages: [1]   Go Up
« previous next »