« previous next »
Pages: [1]   Go Down

Author Topic: OT poor mans signature holding power rings?  (Read 699 times)

0 Members and 2 Guests are viewing this topic.

Offline mtbugle

  • Trade Count: (32)
  • Contributor
  • ***
  • Posts: 355
  • Gender: Male
OT poor mans signature holding power rings?
« on: September 07, 2010, 04:43:13 PM »
If this has to be moved as is not appropriate for this site I appologize in advance. Handi's is where I generaly hang my hat for reading and usually seems to have the most common sense type of folks.  My question is on a hard recoiling gun I am having trouble keeping the scope from sliding forward. Have 30 mm weaver rings that the band over the scope clips on one side and has two screws on other side. I can see that the band only contacts scope in a thin area at top, and will work on lappin bases as good as I can (don't have a 30 mm lap rod yet).  Has anyone ever tried to put a thin layer of black rtv in base of ring for better grip to scope than metal to metal. And posibly inside band area to widen amount of area contacted on scope.  I just don't have $60 for Signature rings now and wonder if this idea is feasible or would actually be more slippery?
thanks Don.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #1 on: September 07, 2010, 04:46:54 PM »
I've used Loctite and even wet/dry sandpaper, both work.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline wreckhog

  • Trade Count: (55)
  • Senior Member
  • *****
  • Posts: 2997
Re: OT poor mans signature holding power rings?
« Reply #2 on: September 07, 2010, 04:53:26 PM »
Wrap 1 layer of electrical tape under the rings and see how easy it is (NOT) to adjust the scope.
Logged

Offline mechanic

  • GBO Supporter
  • Trade Count: (32)
  • Senior Member
  • *****
  • Posts: 5112
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #3 on: September 07, 2010, 06:11:38 PM »
Pure rubber high voltage insulating tape.  Very soft and pliable, and it ain't movin' once you apply that ....just a small strip will do the job.
Logged
Molon Labe, (King Leonidas of the Spartan Army)

Offline Graybeard

  • Administrator
  • Trade Count: (69)
  • Senior Member
  • *****
  • Posts: 26946
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #4 on: September 07, 2010, 06:21:45 PM »
Scopes can move one way only FORWARD. So the easy fix for that is to slide it to where the turret rests on the rear of the front ring. If that gives you scope placement that is OK it's the easiest fix.

Dump the junk Weaver rings and go with Burris Signature tho and all your troubles will be over.
Logged


Bill aka the Graybeard
President, Graybeard Outdoor Enterprises
256-435-1125

I am not a lawyer and do not give legal advice.

Jesus is the way, the truth, and the life anyone who believes in Him will have everlasting life!

Offline jedman

  • GBO Supporter
  • Trade Count: (24)
  • A Real Regular
  • *****
  • Posts: 921
  • Gender: Male
  • Retired and livin the dream !
Re: OT poor mans signature holding power rings?
« Reply #5 on: September 08, 2010, 03:02:31 AM »
   I have used a couple of wraps of teflon tape around the scope tube at the point of contact with the rings, It seems to work good on scopes that you move to different rifles because you dont leave any ring marks on the tube and they dont move.   Jed
Logged
Current handi family, 24 ga./ 58 cal ,50-70,  45 smokeless MZ, 44 belted bodeen, 44 mag,.375 H&R (wildcat),375 Win.,357 max, .340 MF ( wildcat ), 8 mm Lebel, 8x57, .303 British, 270 x 57 R,(wildcat) 256 Win Mag, 2 x 243 Win,2 x 223 Rem. 7-30 Waters &20ga.,

Offline gatersb

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 123
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #6 on: September 08, 2010, 03:16:19 AM »
i used rubber cement on a cva muzzleloader that kept adjusting the scope for me.  300grain bullet with 100 grains of pyrodex
Logged

Offline mtbugle

  • Trade Count: (32)
  • Contributor
  • ***
  • Posts: 355
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #7 on: September 08, 2010, 07:04:15 AM »
Thanks for the ideas. I think that electrical tape will be a lot easier and more reversable if I dont like. I thought about teflon, but thought it was suppose to reduce friction.
Thanks again and if any more ideas please add.
Thanks Don.
Logged

Offline yukondog

  • GBO Supporter
  • Trade Count: (43)
  • Senior Member
  • *****
  • Posts: 1095
Re: OT poor mans signature holding power rings?
« Reply #8 on: September 08, 2010, 07:20:29 AM »
The one thing about tape is that in the heat the glue on the tape will turn to mush, I do electrical work and  I know electrical tape will. High voltage tape or teflon wood work better I would think.
Logged
an unloaded wepon is equal to the same mass and volume as a rock.

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #9 on: September 08, 2010, 08:10:32 AM »
The traditional fix is scope tube and inside of rings CLEAN and DRY. Sprinkle on a bit of Powdered Rosin and reset the scope.
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline mtbugle

  • Trade Count: (32)
  • Contributor
  • ***
  • Posts: 355
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #10 on: September 08, 2010, 11:23:13 AM »
Aw yes, familiar with slipping electrical tape when warm. I can't believe I didn't think of the powdered rosin after I had such a time getting some for the barrel vise I built. It really works well for the barrel vise, That is what I better try for the ring. I assume some in the bottom part but not under the overband, right?
Thanks Don.
Logged

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #11 on: September 08, 2010, 04:11:56 PM »
Try it that way, if it works youve got it. I like to escalate slow........
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline dpe.ahoy

  • GBO Supporter
  • Trade Count: (7)
  • Senior Member
  • *****
  • Posts: 3363
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #12 on: September 08, 2010, 04:53:50 PM »
I like the Weaver Quad locs, never had any problems with them letting any scope slip, about $10.00 at Wally World around here.  Can't find em anywhere else around here.  They have worked on the 444 Marlin and the 45-70.  DP
Logged
RIP Oct 27, 2017

Handi's:22Shot, 22LR, 2-22Mag, 22Hornet, 5-223, 2-357Max, 44 mag, 2-45LC, 7-30 Waters, 7mm-08, 280, 25-06, 30-30, 30-30AI, 444Marlin, 45-70, AND 2-38-55s, 158 Topper 22 Hornet/20ga. combo;  Levers-Marlins:Two 357's, 44 mag, 4-30-30s, RC-Glenfields 36G-30A & XLR, 3-35 Rem, M-375, 2-444P's, 444SS, 308 MX, 338Marlin MXLR, 38-55 CB, 45-70 GS, XS7 22-250 and 7mm08;  BLR's:7mm08, 358Win;  Rossi: 3-357mag, 44mag, 2-454 Casull; Winchesters: 7-30 Waters, 45Colt Trapper; Bolt actions, too many;  22's, way too many.  Who says it's an addiction?

Offline mtbugle

  • Trade Count: (32)
  • Contributor
  • ***
  • Posts: 355
  • Gender: Male
Re: OT poor mans signature holding power rings?
« Reply #13 on: September 08, 2010, 06:12:03 PM »
I have been using the quad locs a lot also, but havn't found in 30mm at wally world.
Thanks Don
Logged
Pages: [1]   Go Up
« previous next »