« previous next »
Pages: [1]   Go Down

Author Topic: Question re: 45-70  (Read 1061 times)

0 Members and 1 Guest are viewing this topic.

Offline wls

  • Trade Count: (0)
  • Member
  • *
  • Posts: 49
Question re: 45-70
« on: January 21, 2011, 02:21:48 PM »
With the new regs allowing 1.80 case lenght, what becomes of psi if I load a 405 lead slug over the normal amount of 5744 in the shorter case?  Should I maintain the normal OAL?
Logged

Offline srussell

  • GBO Supporter
  • Trade Count: (14)
  • A Real Regular
  • *****
  • Posts: 838
Re: Question re: 45-70
« Reply #1 on: January 21, 2011, 07:59:41 PM »
YES
Logged

Offline Vic49

  • GBO Supporter
  • Trade Count: (30)
  • Contributor
  • *****
  • Posts: 483
  • Gender: Male
Re: Question re: 45-70
« Reply #2 on: January 21, 2011, 11:21:36 PM »
The new length is not law yet, just a proposal.
Logged
And what country can preserve its liberties, if its rulers are not warned from time to time, that this people preserve the spirit of resistance? Thomas Jefferson
Handi rifles
Knight, T/C and CVA Muzzleloaders
Bowtech and Diamond bows

Offline ChrisK

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 324
Re: Question re: 45-70
« Reply #3 on: January 23, 2011, 06:52:09 AM »
I got a feeling if they don't pass it there are going to be a lot of people not following the rules because of all the hoopla over changing the rules. There are a lot of people that think that they have changed the case length. The have not and may not everyone should really make sure before gun season opens up!
Logged

Offline Lon371

  • GBO Supporter
  • Trade Count: (53)
  • Senior Member
  • *****
  • Posts: 2486
  • Gender: Male
  • Why Not a Handi?
Re: Question re: 45-70
« Reply #4 on: January 24, 2011, 01:24:26 PM »
 I think  ::) alot of folks just like something new. Even if they do not pass the new length, you can still play with it. Look at how many Indianas have rifles that can not be used for deer.  ;) Myself I think I am going to go with a short chambered .35 Rem.


Lonny
Logged

Offline tobster

  • GBO Supporter
  • Trade Count: (18)
  • A Real Regular
  • *****
  • Posts: 948
Re: Question re: 45-70
« Reply #5 on: January 28, 2011, 02:00:20 AM »
WLS-at the risk of highjacking this thread, I would like to know what method you use to trim your 45-70 cases down to 1.80.
Logged

Offline wls

  • Trade Count: (0)
  • Member
  • *
  • Posts: 49
Re: Question re: 45-70
« Reply #6 on: January 28, 2011, 04:21:25 AM »
Haven't figured that out yet.  Was going to ask the people here.
Logged

Offline Lon371

  • GBO Supporter
  • Trade Count: (53)
  • Senior Member
  • *****
  • Posts: 2486
  • Gender: Male
  • Why Not a Handi?
Re: Question re: 45-70
« Reply #7 on: January 28, 2011, 07:53:47 AM »
 Hank oh Hank, didn't you trim some 45-70 brass down?

 Check post 61  http://www.gboreloaded.com/forums/index.php/topic,220391.60.html

 If he don't show up here, send him a note.

Lonny
Logged

Offline Hank in Indiana

  • Trade Count: (2)
  • Avid Poster
  • **
  • Posts: 118
Re: Question re: 45-70
« Reply #8 on: January 28, 2011, 10:33:54 AM »
I've trimmed with fine hacksaw blades, files, and elect drill attached to the case trimmer. They all work. Anneal after and your brass will last longer.
Logged

Offline possumpacker

  • Trade Count: (0)
  • Member
  • *
  • Posts: 19
Re: Question re: 45-70
« Reply #9 on: October 20, 2011, 07:05:10 AM »
i trimed my cases to 1.63 with copper tubing cutter (4.00at ace hardware) then trimmed to 1.625 on my trimmer. I  load full length 45-70 with 30.5 imr 4198 405 bullet. 45-70 short are loaded with 30.5 gr. imr 4198 and 300 gr bullet this is a lite compressed load very accurate
Logged
Pages: [1]   Go Up
« previous next »