« previous next »
Pages: [1]   Go Down

Author Topic: Burris mounts  (Read 761 times)

0 Members and 1 Guest are viewing this topic.

Offline chazgin

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 110
Burris mounts
« on: December 27, 2003, 06:42:02 AM »
Does anybody have a source for the Burris "no gunsmithing" mounts that fit on the rib for Supermags? I've looked at the B-Square mounts but they appear flimsy.
Logged

Offline FireMarshal91

  • Trade Count: (0)
  • Member
  • *
  • Posts: 36
Scope Mounts
« Reply #1 on: December 27, 2003, 07:01:51 AM »
I have a B-square scope mount on my 6" DW 44 mag. It clamps on well, however, the only complaint I have about the B-square is it seems to sit high on my revolver.  It makes me feel like I have a leg weight on my barrel.  I used it primarity for sighting in handloads for group tests and I used open sights for pistol hunting (easy handling and packing).  B-square is a good mount, just big than I would like.  The burris mounts you can find on e-bay and on gunbroker.com.  Keep an eye out for them, they come and go.

Hope this helps,

JC  8)
Logged
Sometimes you are the dog...

And sometimes you are the hydrant

Offline chazgin

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 110
Hmmm
« Reply #2 on: December 27, 2003, 07:29:26 AM »
The B-Square mount I had in my hands did not seem to fit the gap in the vent rib. The legs were too thick. I saw a Burris mount on a Supermag that was for sale, but the guy would not part with just the mount. This Burris mount was quite a bit lower than the B-square mount and was mode of steel. Looked very nice.
Logged

Offline FireMarshal91

  • Trade Count: (0)
  • Member
  • *
  • Posts: 36
scope mount
« Reply #3 on: December 27, 2003, 08:44:54 AM »
Chazgin

I had to file down the legs that goes under the barrel vent rib a little bit with a fine file.  I don't know if this is normal or not.  Let me know if you get a burris mount and tell me how it works.  I might get one also.

Thx,

JC  8)
Logged
Sometimes you are the dog...

And sometimes you are the hydrant

Offline chazgin

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 110
Got a Burris mount
« Reply #4 on: January 02, 2004, 09:45:26 AM »
Firemarshall, I found a dealer here locally that had a Burris mount. Found the dealer by Emailing Burris. They replied with a local dealer that still had some mounts (they are discontinued from Burris). The mount is much better quality than Bsquare and all steel. I put it on my 357 Supermag (fit the 445 also) and it is very solid. Sits low and for my 2X Burris scope I can use low rings. I can send you a picture if you want. Email me at chazgin@direcway.com
Logged

Offline chazgin

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 110
Picture of Burris Mount
« Reply #5 on: January 03, 2004, 08:40:27 AM »
Burris mount on SuperMag

Logged

Offline David Carey

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 266
Burris scope mount
« Reply #6 on: January 16, 2004, 12:00:36 PM »
Here is a picture of the Burris mount with part numbers if that will help anyone, sorry I had just sold it on ebay. I personally did not like the fit on my DW 445, I purchased a ten inch barrel with the drilled and taped scope mount directly from DW.

Dave Carey

[/img]
Logged
NRA Life Member

Offline David Carey

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 266
drilled mount
« Reply #7 on: January 16, 2004, 12:08:42 PM »
Picture of my 445 with 10"bbl.



Dave
Logged
NRA Life Member
Pages: [1]   Go Up
« previous next »