« previous next »
Pages: [1]   Go Down

Author Topic: Pachmayr forend on octagon barrel??  (Read 869 times)

0 Members and 3 Guests are viewing this topic.

Offline ralfus

  • GBO Supporter
  • Trade Count: (6)
  • Avid Poster
  • *****
  • Posts: 106
Pachmayr forend on octagon barrel??
« on: September 27, 2011, 06:47:34 PM »
I was wondering how well an octagon 10" fits with a Pachmayr forend. My recent octagon barrel is on layaway for a little bit. Any pics??
Logged

Offline Austin from NC

  • Racjarrett88
  • Trade Count: (12)
  • Contributor
  • ***
  • Posts: 410
  • Gender: Male
  • Proudest Uncle Ever
Re: Pachmayr forend on octagon barrel??
« Reply #1 on: September 27, 2011, 07:55:21 PM »
If your talking about the g2 forend I have a 10 inch octagon on the way I will tell you when it gets here. Old pachmayr had hanger bars didn't they? Don't know about them.

       Austin
Logged
(choot it, choot it Elizabeth, choot it) Troy Landry

Offline Da-Law-Dawg

  • Trade Count: (4)
  • Avid Poster
  • **
  • Posts: 102
  • Gender: Male
Re: Pachmayr forend on octagon barrel??
« Reply #2 on: September 28, 2011, 01:59:57 PM »
The Pachmyer Contender fore-end uses a hanger bar as Austin states.

Dunno if it'll work on the octagonal barrels due to the taper. The rear screw will line up but don't know how sturdy it'll be.
Logged

Offline butchen

  • Trade Count: (3)
  • Avid Poster
  • **
  • Posts: 171
Re: Pachmayr forend on octagon barrel??
« Reply #3 on: September 28, 2011, 04:10:30 PM »
it works fine, just like on a 10" round barrel. I have had no prob. don't know if anyone has never heard of any.
Logged
Government is not the solution to our problems. Government is the problem. – Ronald Reagan

When the people fear their government, there is tyranny; when the government fears the people, there is liberty." - Thomas Jefferson

I always thank my God for you because of his grace given you in Christ Jesus.For in him you have been enriched in every way—with all kinds of speech and with all knowledge— - 1 Corinthians 1:4-5

Offline ralfus

  • GBO Supporter
  • Trade Count: (6)
  • Avid Poster
  • *****
  • Posts: 106
Re: Pachmayr forend on octagon barrel??
« Reply #4 on: September 28, 2011, 05:34:19 PM »
Quote from: butchen on September 28, 2011, 04:10:30 PM
it works fine, just like on a 10" round barrel. I have had no prob. don't know if anyone has never heard of any.
Sounds good. Do you bypass the hanger and just mount through the forend hole into the barrel? My octagon barrel has the hole "in the middle"
Logged

Offline Mtn Jack

  • Trade Count: (1)
  • Member
  • *
  • Posts: 59
  • Gender: Male
  • western Pa patriot
Re: Pachmayr forend on octagon barrel??
« Reply #5 on: September 28, 2011, 06:17:38 PM »
I think  my .357 is a 6 inch oct, and looks cool with the pacs on it. It has the hanger bar but i think it just uses one of the holes. I also have the pac gripper grip on the back, sorta looks like a manlicker. sp
Logged
Friends may enter, others not, friends will be fed and others shot.

Offline butchen

  • Trade Count: (3)
  • Avid Poster
  • **
  • Posts: 171
Re: Pachmayr forend on octagon barrel??
« Reply #6 on: September 29, 2011, 10:39:44 AM »
Quote from: ralfus on September 28, 2011, 05:34:19 PM
Quote from: butchen on September 28, 2011, 04:10:30 PM
it works fine, just like on a 10" round barrel. I have had no prob. don't know if anyone has never heard of any.
Sounds good. Do you bypass the hanger and just mount through the forend hole into the barrel? My octagon barrel has the hole "in the middle"
on mine the hanger was used. I have never seen one with the mount there. So my help was useless, sorry.
Logged
Government is not the solution to our problems. Government is the problem. – Ronald Reagan

When the people fear their government, there is tyranny; when the government fears the people, there is liberty." - Thomas Jefferson

I always thank my God for you because of his grace given you in Christ Jesus.For in him you have been enriched in every way—with all kinds of speech and with all knowledge— - 1 Corinthians 1:4-5

Offline ralfus

  • GBO Supporter
  • Trade Count: (6)
  • Avid Poster
  • *****
  • Posts: 106
Re: Pachmayr forend on octagon barrel??
« Reply #7 on: September 29, 2011, 01:52:03 PM »
Quote from: butchen on September 29, 2011, 10:39:44 AM
Quote from: ralfus on September 28, 2011, 05:34:19 PM
Quote from: butchen on September 28, 2011, 04:10:30 PM
it works fine, just like on a 10" round barrel. I have had no prob. don't know if anyone has never heard of any.
Sounds good. Do you bypass the hanger and just mount through the forend hole into the barrel? My octagon barrel has the hole "in the middle"
on mine the hanger was used. I have never seen one with the mount there. So my help was useless, sorry.
You were still a big help, thanks! I have a hanger available if needed.
Logged
Pages: [1]   Go Up
« previous next »