« previous next »
Pages: [1]   Go Down

Author Topic: K-Hornet dies?  (Read 1883 times)

0 Members and 2 Guests are viewing this topic.

Offline Monteria

  • GBO Supporter
  • Trade Count: (8)
  • Avid Poster
  • *****
  • Posts: 114
K-Hornet dies?
« on: November 02, 2011, 02:40:26 PM »
Does anyone know if the LEE .22 Hornet collet neck size only dies have enough shoulder clearance for the K-Hornet?

I have an issue spending 2-3X for a set of specialty neck size only dies, when they are likely the same exact die as the non improved neck size only version.

Thanks
Logged

Offline Torwe

  • GBO Supporter
  • Trade Count: (33)
  • Avid Poster
  • *****
  • Posts: 180
  • Gender: Male
Re: K-Hornet dies?
« Reply #1 on: November 02, 2011, 02:55:52 PM »
No their not.  But.......you can send you collet die to Lee and they will modify it to K hornet. They charged me $10.00 including return shipping
Logged
Life is like a coin you can spend it any way you wish. But you can only spend it once.

Offline Monteria

  • GBO Supporter
  • Trade Count: (8)
  • Avid Poster
  • *****
  • Posts: 114
Re: K-Hornet dies?
« Reply #2 on: November 09, 2011, 01:54:21 PM »
For Anyones future reference, the standard .22 Hornet LEE collet neck size only dies just showed up and have plenty of sholder clearance to size K-Hornets almost all the way to the shoulder, without impact. Perfectly sufficient for anything short of full length sizing at half to 1/3 the price of K-Hornet dies.
Logged

Offline Jason F

  • Trade Count: (261)
  • Senior Member
  • *****
  • Posts: 2105
  • Gender: Male
Re: K-Hornet dies?
« Reply #3 on: November 09, 2011, 02:34:46 PM »
What did you do just adjust it down to the neck?
Logged
handi rifles- 22 mag      22 hornet    223      7mm-08      308 chip shot     30-30 x2     30-06 shorty      358 cheez whiz     357 max     35 remington     375-08    410 rifled slug     454 casull     460 s&w     45 smokeless muzzleloader x2     45-70    50 huntsman    50-70 government shikari     20 ga.ush     12 ga.ush    12 ga.3 1/2     10 ga.imp.cyl. slug gun

Offline jeepmann1948

  • GBO Supporter
  • Trade Count: (67)
  • Senior Member
  • *****
  • Posts: 1422
  • Gender: Male
  • San Angelo, Texas
Re: K-Hornet dies?
« Reply #4 on: November 10, 2011, 12:16:41 AM »
I found my 22K Hornet dies on Ebay. They were 20 or so dollars with shipping.I went with the K version not for velocity increase but for a longer case life.So far I have been very pleased with the mod.
Logged
"it ain't what you shoot em with......................
  it's where you hit em "

Offline Monteria

  • GBO Supporter
  • Trade Count: (8)
  • Avid Poster
  • *****
  • Posts: 114
Re: K-Hornet dies?
« Reply #5 on: November 10, 2011, 01:08:50 AM »
Jeep, I did it for the same reason. Thats also why I am intent on neck sizing only.

Jason, The same way you would set any die. I just stopped adjusting the die down, short of reaching the shoulder.


Logged

Offline LaOtto222

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 3828
  • Gender: Male
Re: K-Hornet dies?
« Reply #6 on: November 10, 2011, 05:21:54 AM »
I have a Redding die set for my 22K Hornet. I also have a 22 Hornet collet die, but have been using a Redding Type "S" neck sizing die I have for the 221 Fireball. It makes some very good handloads


Here is a typical group with a cheap MidSouth Varmint Nightmare 34 grain Hollow point bullet.





I originally wanted to get a Lee Collet die (I really do like them) for my 221 Fireball. I sent in two fired cases and two bullets (50 grain V-Max) with a check for $54 (I think). they sent it all back to me with a note saying the 221 Fireball was too short to make a collet die for. the 22 Hornet is the exact same length, and it is the an off the shelf item...go figure. Any way that is how I ended up with the Redding neck sizing die. Since the 221 Fireball and the 22K Hornet are the same length, I though I would give it a try and it worked to perfection.


Good Luck and Good Shooting


 
Logged
Great men have vision and resolve to make dreams come true.
Pages: [1]   Go Up
« previous next »