« previous next »
Pages: [1]   Go Down

Author Topic: Need some info on grips  (Read 1021 times)

0 Members and 1 Guest are viewing this topic.

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Need some info on grips
« on: November 12, 2011, 02:35:20 PM »
I picked up a set of grips today at an estate sale that were in a box marked Colt SAA, made from ivory micarta, and have "Made in the Philippines for TYLER TRU-FIT" and "#3" on the inside. Unfortunately they do not fit my USFA or anything else I compared them to. The front is way shorter than a SAA grip, and they are not flat on top but rather have a notch cut into them. Anybody know what these are made for?
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Need some info on grips
« Reply #1 on: November 12, 2011, 06:45:29 PM »
Might find answers by checking pictures here to compare which you have.  ;)
 
http://www.t-grips.com/
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: Need some info on grips
« Reply #2 on: November 13, 2011, 02:28:25 AM »
If that is the same company they don't make grips anymore. Just the T-grip metal adapters. I am not so sure the ones I have are made by the same outfit, though the have the same name. I was going to call them and ask at some point.
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Need some info on grips
« Reply #3 on: November 13, 2011, 01:31:11 PM »
 
SMITH & WESSON
REVOLVERS
[/t]
[/t]
MODEL SIZE
For ALL Smith & Wesson "J" frames; models: 30, 31, 34, 36, 37, 38, 47, 60, 63, 649, ect..., made after 1955. Chief, Kit Gun, Bodyguard, Centennial, hand Ejector, ect, also most Charter Arms, Rossi 38 Special, Taurus 85, R.G. Model 31. All guns must have standard factory panel grips, will not fit oversize or rubber grips.
1
For Smith & Wesson "J" frame revolvers made before 1955. Chief, Terrier, etc. Also for EIG E9, INA, Tiger, Llama X111, some late model Charter Arms, with standard grips.
2
For ALL Smith & Wesson "K" and "L" SQUARE BUTT frame revolvers; models: 10, 12, 13, 14, 15, 17, 18, 19, 48, 64, 65, 66, 67, 547, 581, 586, ect...,. Also fits Astra Cadix, Falcon Revolvers with standard size regular grips, will not fit oversize grips. SQUARE BUTT "K" & "L" FRAMES.
3
For ALL Smith & Wesson "K" & "L" frame ROUND BUTT: models: 10, 12, 13, 19, 64, 65, 66, 547, 586, ect... and all "K" frame ROUND BUTT models with regular standard size grips, will not fit oversize grips.
3R
For ALL Smith & Wesson "N" frame; models: 22, 25, 27, 28, 29, 57, 58, 629, ect... Patrolman, Outdoorsman, Target Military, 1918 Military, also Miroku, Aster 357, Llama Heavy Frame Revolvers all with standard size grips, will not fit oversize grips. Round or Square butt does not matter for N-Frame Revolvers.
4
[/t]
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Need some info on grips
« Reply #4 on: November 13, 2011, 01:32:10 PM »
Sorry it changed when I hit post.  Yours was the #3, so it is for a Smith & Wesson K & L square butt frame revolvers on that chart. 
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: Need some info on grips
« Reply #5 on: November 15, 2011, 01:09:36 AM »
Hi, thanks for that list. But it ain't for a S&W. They look like SAA grips but slightly different. Nothing like S&W grips. I still have a mystery here, the funny thing is if I ever find out what they fit I'll probably need to buy one to have something to put these neato grips on.
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline tacklebury

  • GBO Supporter
  • Trade Count: (12)
  • Senior Member
  • *****
  • Posts: 3633
  • Gender: Male
  • Central Michigan
Re: Need some info on grips
« Reply #6 on: November 15, 2011, 02:17:35 PM »
lol Strange predicament. ;)
Logged
Tacklebury --}>>>>>    Multi-Barrel: .223 Superlite, 7mm-08 22", .30-40 Krag M158, .357 Maximum 16-1/4 HB, .45 Colt, .45-70 22" irons, 32" .45-70 Peeps, 12 Ga. 3-1/2 w/ Chokes, .410 Smooth slugger, .45 Cal Muzzy, .50 Cal Muzzy, .58 Cal Muzzy

also classics: M903 9-shot Target .22 Revolver, 1926 .410 Single, 1915 38 S&W Break top Revolver and 7-shot H&R Trapper .22 6" bbl.

Pages: [1]   Go Up
« previous next »