« previous next »
Pages: [1]   Go Down

Author Topic: 44 spc/44mag die  (Read 385 times)

0 Members and 1 Guest are viewing this topic.

Offline tom548

  • GBO Supporter
  • Trade Count: (51)
  • A Real Regular
  • *****
  • Posts: 693
  • Gender: Male
44 spc/44mag die
« on: December 11, 2011, 01:37:36 PM »
I have a CH 44 spc/mag sizing die that came with some misc dies. I went to size a 44 mag case with it today and it adds a slight shoulder and necked down the case like a 44-40. The neck starts about 7/8" to 15/16" from the rim of the case. Any Idea what this is other than a miss marked die. Thanks Tom
(Note added: I have been reloading for over 40 years, every thing was set up correctly)
Logged

Offline cwlongshot

  • GBO Supporter
  • Trade Count: (158)
  • Senior Member
  • *****
  • Posts: 9907
  • Gender: Male
  • Shooting, Hunting, the Outdoors & ATVs
Re: 44 spc/44mag die
« Reply #1 on: December 11, 2011, 02:00:07 PM »
First thing I thought was same as you, 44-40...Look the makkins over closer, does it say 44WCF?
 
Maybe pull it appart and give it a good cleaning.
 
CW
Logged
"Pay heed to the man who carries a single shot rifle, he likely knows how to use it."

NRA LIFE Member 
Remember... Four boxes keep us free: the soap box, the ballot box, the jury box, and the cartridge box.

Offline Tom W.

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1294
  • Gender: Male
  • Warning... Does not play well with others!
Re: 44 spc/44mag die
« Reply #2 on: December 11, 2011, 02:02:00 PM »
Either try screwing your die up or use a washer under it to get the proper height. I'ts badly misadjusted.
Logged
Tom
Alabama Hunter and firearms safety instructor

I really like my handguns!

Offline tom548

  • GBO Supporter
  • Trade Count: (51)
  • A Real Regular
  • *****
  • Posts: 693
  • Gender: Male
Re: 44 spc/44mag die
« Reply #3 on: December 11, 2011, 04:00:30 PM »
It is clean and been  checked with a light and mag. glass. It has a shoulder and smaller neck built into it.  The writing is 44 spl/mag as I said in first post. The shoulder starts about 7/8 th" from bottom of die. MY first thought maybe something was just stuck in it, but it is one solid piece.
Logged

Offline tom548

  • GBO Supporter
  • Trade Count: (51)
  • A Real Regular
  • *****
  • Posts: 693
  • Gender: Male
Re: 44 spc/44mag die
« Reply #4 on: December 11, 2011, 04:06:32 PM »
Tom W; if I did as you suggest then I would only size  about 1/2 the 44 mag case. It should be  straight walled  die and should not have a shoulder in it. I can't adj the shoulder. It was in the proper adj when I ran the case thought it.
Logged

Offline Tom W.

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1294
  • Gender: Male
  • Warning... Does not play well with others!
Re: 44 spc/44mag die
« Reply #5 on: December 13, 2011, 01:27:56 PM »
Sorry.. That was just the first thought that came to my feeble mind.. I had a busy weekend!
Logged
Tom
Alabama Hunter and firearms safety instructor

I really like my handguns!
Pages: [1]   Go Up
« previous next »