« previous next »
Pages: [1]   Go Down

Author Topic: Getting the lead out of a mold  (Read 1460 times)

0 Members and 1 Guest are viewing this topic.

Offline bulletstuffer

  • Trade Count: (25)
  • A Real Regular
  • ****
  • Posts: 694
  • Gender: Male
  • Overkill begins when hair shoots out the antlers.
Getting the lead out of a mold
« on: December 14, 2011, 02:46:15 AM »
Hi guys.  Had a stupid day :(   I got lead in the two holes that align the mold when closing it.  How do I get the lead out?
 
Thanks for the help.
 
Bulletstuffer
Logged
I am the first to work when I have to and the first to go on vacation when I can!  God Bless America!!!

Offline anachronism

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 269
Re: Getting the lead out of a mold
« Reply #1 on: December 14, 2011, 01:22:17 PM »
I'm assuming the hole goes all the way through the mould. Try pushing it out with a properly sized punch. If it's a blind hole. you may need to try threading a screw into the lead & pulling it back out the way it went in.
Logged

Offline srussell

  • GBO Supporter
  • Trade Count: (14)
  • A Real Regular
  • *****
  • Posts: 838
Re: Getting the lead out of a mold
« Reply #2 on: December 14, 2011, 01:46:51 PM »
 heat it up
Logged

Offline Lloyd Smale

  • Moderators
  • Trade Count: (32)
  • Senior Member
  • *****
  • Posts: 18262
Re: Getting the lead out of a mold
« Reply #3 on: December 15, 2011, 01:49:51 AM »
yup heat it up with a torch or stick in in the hot pot till they melt.
Quote from: srussell on December 14, 2011, 01:46:51 PM
heat it up
Logged
blue lives matter

Offline luckydawg13

  • GBO Supporter
  • Trade Count: (27)
  • A Real Regular
  • *****
  • Posts: 982
  • Gender: Male
Re: Getting the lead out of a mold
« Reply #4 on: December 16, 2011, 04:53:11 AM »
Quote from: Lloyd Smale on December 15, 2011, 01:49:51 AM
yup heat it up with a torch or stick in in the hot pot till they melt.
Quote from: srussell on December 14, 2011, 01:46:51 PM
heat it up
heat it up
Logged
kids that hunt and fish dont mug old Ladies
and drive a F150

Offline bulletstuffer

  • Trade Count: (25)
  • A Real Regular
  • ****
  • Posts: 694
  • Gender: Male
  • Overkill begins when hair shoots out the antlers.
Re: Getting the lead out of a mold
« Reply #5 on: December 16, 2011, 06:09:14 AM »
Heat it up it is ;)   I ran some hot lead over it but probably did not get it hot enough last time.  I really appreciate the help!


Merry Christmas,


Bulletstuffer
Logged
I am the first to work when I have to and the first to go on vacation when I can!  God Bless America!!!

Offline .22-5-40

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 253
Re: Getting the lead out of a mold
« Reply #6 on: December 16, 2011, 10:51:52 AM »
Hello, Bulletstuffer.  One thing I do before casting is to use Rapine (or other brand) Mould prep on top, bottom, all over sprue cutter, pins & their locating holes.  This not only provides some lubrication, it also helps prevent lead sticking.  A No.2 pencil is also used to scribble all over bottom of plate..& top of blocks, for same reason.  you could twirl it around in pin holes also.  Best of luck!
Logged

Offline Anduril

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 335
Re: Getting the lead out of a mold
« Reply #7 on: December 16, 2011, 10:59:58 AM »
My first reaction was "melt it out".
Glad to see others agree.
..
 
Logged
Pages: [1]   Go Up
« previous next »