« previous next »
Pages: [1]   Go Down

Author Topic: Thumb hole stock question  (Read 458 times)

0 Members and 1 Guest are viewing this topic.

Offline geezerbiker

  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 1884
  • Gender: Male
Thumb hole stock question
« on: May 21, 2012, 11:57:00 AM »
I'm thinking really hard about ordering a thumb hole stock set from Boyds and I'm wondering if the bolt hole will chafe my hand.  Has any one here had the problem with with one?

Tony
Logged

Offline dave29

  • GBO Supporter
  • Trade Count: (93)
  • Senior Member
  • *****
  • Posts: 1256
Re: Thumb hole stock question
« Reply #1 on: May 21, 2012, 12:04:31 PM »
The hole hasn't bothered me. I have 3 Lam thumbholes.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: Thumb hole stock question
« Reply #2 on: May 21, 2012, 01:05:49 PM »
I've shot about 60 rounds thru my 45-70 Ultra Hunter, 40 of those were Ruger loads with no issues. Also a several dozen each thru the 221, 6.5x55, 7x57, 243 and 6mm Ackley, hasn't been a problem for me.  ;) That's with a button socket head bolt, if it has a regular socket head bolt, the results may be different, the button head is quite a bit lower profile and doesn't protrude from the stock like the standard socket head does.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline reclusej

  • GBO Supporter
  • Trade Count: (10)
  • Avid Poster
  • *****
  • Posts: 172
  • Gender: Male
Re: Thumb hole stock question
« Reply #3 on: May 22, 2012, 05:34:00 AM »
I have a couple of thumb hole stocks and I have no
problem with that. Really like the way they feel.
                                            reclusej   :) 8)
Logged
I own a gun , not to kill some one but
so no one tries to kill me !!!

Offline cwlongshot

  • GBO Supporter
  • Trade Count: (158)
  • Senior Member
  • *****
  • Posts: 9907
  • Gender: Male
  • Shooting, Hunting, the Outdoors & ATVs
Re: Thumb hole stock question
« Reply #4 on: May 22, 2012, 07:50:59 AM »
The guys say and I agree I do not think you will have any problems.
I have two issues with the thumb hole. First is its harder to manipulate the hammer. Second is the comb is too low.  Other than that, I like the feel better then a std stock.

CW
Logged
"Pay heed to the man who carries a single shot rifle, he likely knows how to use it."

NRA LIFE Member 
Remember... Four boxes keep us free: the soap box, the ballot box, the jury box, and the cartridge box.

Offline geezerbiker

  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 1884
  • Gender: Male
Re: Thumb hole stock question
« Reply #5 on: May 22, 2012, 09:31:36 PM »
Thanx guys.  I hadn't considered that the comb height would different.  I'll have to wait until I can handle one before I order.   I was panning to install a new thumb hole set on my .223 and put it's stock and for end on my .44 mag to dispose of the plastic stock...

Tony
Logged
Pages: [1]   Go Up
« previous next »