« previous next »
Pages: [1]   Go Down

Author Topic: GolfBall Coehorn  (Read 742 times)

0 Members and 2 Guests are viewing this topic.

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
GolfBall Coehorn
« on: July 06, 2012, 10:49:37 AM »
With guidance from the good folks of the GO2GBO Forum I was able to complete a GolfBall Coehorn:
Logged

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #1 on: July 06, 2012, 10:51:35 AM »
After machining:
Logged

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #2 on: July 06, 2012, 10:55:31 AM »
The mortar bed is laminated red oak cut on a table saw, holes bored with a drill press.
All surfaces cleaned up with a hand chisel.

The glow in the barrel is from a bright orange golf ball that I inserted for contrast.
Logged

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #3 on: July 06, 2012, 10:56:09 AM »
And the initial firing was a blast :)

Video should be ready for upload tonight.

I'm done, thread is open.

Logged

Offline keith44

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 2748
  • Gender: Male
Re: GolfBall Coehorn
« Reply #4 on: July 06, 2012, 11:43:58 AM »
 8)  Looking forward to the video!  Nicely done
Logged
keep em talkin' while I reload
Life member NRA

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #5 on: July 06, 2012, 12:27:57 PM »
More photos added above.
Logged

Offline Cat Whisperer

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 7493
  • Gender: Male
  • Pulaski Coehorn Works
Re: GolfBall Coehorn
« Reply #6 on: July 07, 2012, 05:11:07 AM »
Good pix!  Thanks,

I like your setup on machining the trunnion.
Logged
Tim K                 www.GBOCANNONS.COM
Cat Whisperer
Chief of Smoke, Pulaski Coehorn Works & Winery
U.S.Army Retired
N 37.05224  W 80.78133 (front door +/- 15 feet)

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #7 on: July 07, 2012, 05:24:35 AM »
Quote from: Cat Whisperer on July 07, 2012, 05:11:07 AM
Good pix!  Thanks,

I like your setup on machining the trunnion.

Rotary table on the milling machine worked out pretty well for the trunnion machining
Logged

Offline Rock6.3

  • Trade Count: (0)
  • Member
  • *
  • Posts: 48
Re: GolfBall Coehorn
« Reply #8 on: July 08, 2012, 06:24:48 PM »
Logged
Pages: [1]   Go Up
« previous next »