« previous next »
Pages: [1]   Go Down

Author Topic: chamber length questions  (Read 563 times)

0 Members and 1 Guest are viewing this topic.

Offline chefjeff

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 472
chamber length questions
« on: August 13, 2012, 12:31:39 PM »
Just bought an old Ithaca double made in 1924. Has 2 and 5/8 inch chambers.This will not be shot much.Will I hurt the gun or myself with 2 and 3/4 inch handicap loads? I used to see 2 and 1/2 inch british guns,maybe I should get some of those. Need a little advice from y'all. Thanks.
Logged

Offline Doublebass73

  • GBO Supporter
  • Trade Count: (46)
  • Senior Member
  • *****
  • Posts: 4579
Re: chamber length questions
« Reply #1 on: August 13, 2012, 01:00:52 PM »
Don't even risk it when you can just buy some of these:
http://www.rstshells.com/rst_classic_shotshells_shotshells.htm

They have 2" and 2 1/2" in 12 gauge and 2 1/2" in every other gauge.
Logged
"Necessity is the plea for every infringement of human freedom. It is the argument of tyrants; it is the creed of slaves."

---- William Pitt (the Younger), Speech in the House of Commons, November 18, 1783

Offline Wyo. Coyote Hunter

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1839
Re: chamber length questions
« Reply #2 on: August 13, 2012, 03:01:54 PM »
 ;) I had the chambers in my grandfather's old Fox lengthened for a modest price..I don't think it is a difficult job..
Logged

Offline jedman

  • GBO Supporter
  • Trade Count: (24)
  • A Real Regular
  • *****
  • Posts: 924
  • Gender: Male
  • Retired and livin the dream !
Re: chamber length questions
« Reply #3 on: August 14, 2012, 01:54:05 AM »
Jeff,    Does your gun have the 2 5/8" stamped on the barrels or did you measure it yourself ?   The reason I ask is I owned a early Ithica 20 ga. double and it was not marked as to chamber length and I shot thousands of 2 3/4" skeet loads thru it without issue.
   I just measured some fired 20 ga. cases and they average 2.675 " so only about 50 thousands over. Shotgun chambers have a slight taper from the breech end forward, I would try to get a accurate measurement of your chambers and if there isnt a defined ridge or abrupt sholder short of 2 3/4" I would go ahead and shoot it with 2 3/4" shells.
 Different gun makers use different chamber dimensions and yours may be OK, my Ithica was the early Fleus style, not a NID ( new improved double ) and I beleive was earlier built than yours.
   Jedman
Logged
Current handi family, 24 ga./ 58 cal ,50-70,  45 smokeless MZ, 44 belted bodeen, 44 mag,.375 H&R (wildcat),375 Win.,357 max, .340 MF ( wildcat ), 8 mm Lebel, 8x57, .303 British, 270 x 57 R,(wildcat) 256 Win Mag, 2 x 243 Win,2 x 223 Rem. 7-30 Waters &20ga.,

Offline DeerSlayer777

  • Trade Count: (7)
  • Avid Poster
  • **
  • Posts: 113
Re: chamber length questions
« Reply #4 on: August 14, 2012, 02:23:14 AM »
I wouldnt do it.  Neither would i have the chamber lengthened. Keep it original.
Logged
Pages: [1]   Go Up
« previous next »