« previous next »
Pages: [1]   Go Down

Author Topic: 12 guage on sb2  (Read 845 times)

0 Members and 1 Guest are viewing this topic.

Offline wonderbowyer087

  • Trade Count: (3)
  • Member
  • *
  • Posts: 36
  • Gender: Male
12 guage on sb2
« on: October 09, 2012, 03:48:55 AM »
I know I can't put my rifle stuff on an sb1 reciever but can I put my spare 12 guage full mod on my sb2?
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: 12 guage on sb2
« Reply #1 on: October 09, 2012, 04:13:44 AM »
Yes, it will work fine as long as it fits, see barrel fitting in the FAQs.  ;)

This doesn't apply to a 12ga USH barrel tho for anyone interested, it's a 10ga size barrel and requires an SB2 10ga shotgun frame.

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline jpshaw

  • GBO Supporter
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1063
  • Gender: Male
Re: 12 guage on sb2
« Reply #2 on: October 09, 2012, 05:13:19 AM »
As stated if it fits, it works.  The SB2 is about an oz lighter, I think.  I had planned to have a 22" 20 Ga youth barrel fitted to my SB2 frame but finally found I could get the whole shotgun used at a Pawn shop cheaper.  Changed the Youth stock for a full length one and then thinned it down and shaped it to straight (Do that with all my shotguns).
Logged

Offline mac66

  • Trade Count: (0)
  • Member
  • *
  • Posts: 16
Re: 12 guage on sb2
« Reply #3 on: October 09, 2012, 04:27:32 PM »
Quote from: wonderbowyer087 on October 09, 2012, 03:48:55 AM
I know I can't put my rifle stuff on an sb1 reciever but can I put my spare 12 guage full mod on my sb2?

You can put low pressure rifle and pistol caliber barrels on an SB1. They are not too hard to fit.  Low pressure meaning 30-30, 35 Rem, 45-70, 444 marlin etc and of course just about any pistol caliber.
Logged

Offline jpshaw

  • GBO Supporter
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1063
  • Gender: Male
Re: 12 guage on sb2
« Reply #4 on: October 10, 2012, 01:59:23 AM »
I know that .30-30 and .45-70 were once fitted to SB1 frames and I believe .44, .357 come with them now.  I've never heard of a .444 fitted to one though since the Saami is 44,000 cup. 
Logged

Offline keith44

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 2748
  • Gender: Male
Re: 12 guage on sb2
« Reply #5 on: October 13, 2012, 10:47:11 AM »
I would not fit any rifle caliber to an SB1 frame.  Pistol calibers sure (excluding the .500 S&W and similar high pressure chamberings).

Logged
keep em talkin' while I reload
Life member NRA

Offline mac66

  • Trade Count: (0)
  • Member
  • *
  • Posts: 16
Re: 12 guage on sb2
« Reply #6 on: October 20, 2012, 03:52:51 AM »
Quote from: jpshaw on October 10, 2012, 01:59:23 AM
I know that .30-30 and .45-70 were once fitted to SB1 frames and I believe .44, .357 come with them now.  I've never heard of a .444 fitted to one though since the Saami is 44,000 cup.

I just looked up the pressure listed for the 444 as both 42K or 44K.  The 30-30 is 42K so the 444 is the same at the lower pressure. I admit that I've never seen or heard of a 444 bbl for these guns so I might be mistaken.
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: 12 guage on sb2
« Reply #7 on: October 20, 2012, 04:48:11 AM »
The 444 has the same case head as the 30-06 at .470" which increases the breech thrust about 1400lbs over the 30-30 @ 42kpsi. The 444 has only been offered by H&R/NEF on a steel SB2 frame, never on a cast iron frame.

Tim 
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain
Pages: [1]   Go Up
« previous next »