Author Topic: Minimum Ham Radio hardware requirements  (Read 1102 times)

0 Members and 1 Guest are viewing this topic.

Offline Dixie Dude

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 4129
  • Gender: Male
Minimum Ham Radio hardware requirements
« on: October 22, 2012, 08:00:04 AM »
What are the minimum hardware requirements for getting into Ham radio?  Any idea of the cost of equipment?
I know of a local electronic store that has classes on getting your Ham radio liscense.  Haven't asked them yet.  I know the internet kind of took over with emails, etc.  But if the internet goes down, then Ham radio is all that is left for person to person communications.

Offline Ranger99

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 9581
Re: Minimum Ham Radio hardware requirements
« Reply #1 on: October 22, 2012, 01:26:48 PM »
a while back, i was gonna get one,
and they came out with the "no code"
license that waived the morse code
requirement and restricted the licensee
to certain frequencies. before i took the test,
f.r.s. and g.m.r.s. radios hit the market, and
i never completed the test. it may be way
different now, so check with a local ham club
and i'll bet they can fix you up. more than
likely they'll walk you through it to help get
you certified and up and running.
18 MINUTES.  . . . . . .

Offline Dixie Dude

  • Trade Count: (6)
  • Senior Member
  • *****
  • Posts: 4129
  • Gender: Male
Re: Minimum Ham Radio hardware requirements
« Reply #2 on: October 22, 2012, 01:46:22 PM »
I think the FRS is the walkie talkie frequencies?  Aren't they.  What is the GMRS?  Can you explain the difference.  I know with the full Ham Radio you can access people around the world.  Do thy have set aside emergency frequencies?  I think with CB's there once was what, channel 7 was supposed to be for emergency only? 

Offline Ranger99

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 9581
Re: Minimum Ham Radio hardware requirements
« Reply #3 on: October 22, 2012, 03:29:53 PM »
f.r.s. and g.m.r.s. are like you say,
"souped up " walkie talkies.


frs - family radio service requires no licensing
and is a short range broadcast 2 + miles?
gmrs- general mobile radio service has the frs
 channels and additional channels that require a
license to broadcast on.
frs is limited to 1/2 a watt broadcasting and
gmrs is permitted up to 50 watts on the gmrs only
channels depending on the type of station.


you likely won't receive any world tranmissions
on these, i would guess depending on atmospheric
conditions, and you sure won't be transmitting any.


channel 9 was the cb emergency station.


most frs and gmrs unit are very low cost compared
to a ham transceiver. it's something more for short
range comms like a walkie talkie.
18 MINUTES.  . . . . . .

Offline Ranger99

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 9581
Re: Minimum Ham Radio hardware requirements
« Reply #4 on: October 22, 2012, 03:31:25 PM »
i'm thinking it's 462mhz or something close :-\
18 MINUTES.  . . . . . .

Offline cabledad

  • Life Member of the NRA Cable Pioneer
  • GBO Supporter
  • Trade Count: (1)
  • Avid Poster
  • *****
  • Posts: 109
  • Gender: Male
Re: Minimum Ham Radio hardware requirements
« Reply #5 on: October 22, 2012, 03:38:06 PM »
Ham radio is like shooting sports,you can spend all you want to. I saw a very small walky talky 2 meter and 440 meter for $65.Brand new made in china.Or you can buy one of these deskfull of transievers that does it all for lots of money. You need to find a local ham operator to show you whats around. I am 69 years old and I have been a ham since I was 14. Everbody is into something different.Good luck  Chuck K5PVP