Author Topic: My custom Norinco  (Read 1054 times)

0 Members and 1 Guest are viewing this topic.

Offline jaysouth

  • Trade Count: (3)
  • Member
  • *
  • Posts: 55
My custom Norinco
« on: October 23, 2012, 04:24:55 PM »
Took over a year on this one.  I  spend a whole winter stippling the front strap and Ed Brown mainspring housing.  C&S ignition parts, Ed Brown barrel and bushing. Navidrex grips.
I had a professional pistolsmith fit the ignition parts for a 3-4 pound pull and fit the barrel.  Gun was parked and then cerra-coated.  It is matte with a capital M!  Illumination for this photo was a 400 watt worklight.  Front sight is staked Millett, rear is Harrison.  Sight  picure is very crisp and functional.
If someone would make a GI beavertail with memory pad, this pisol would be perfection. 

The gun shoots anything that will fit in the magazines.  My favorite load is a 215 SWC from magnus bullet at about 875 fps.

 

Offline Mikey

  • GBO Supporter
  • Moderator
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 8734
Re: My custom Norinco
« Reply #1 on: October 25, 2012, 02:08:42 AM »
Jay - looks good, howz she shoot?  GI memory pad beavertail?  Not so sure if anyone makes those - lots of other style beavertails with memory pads but those most often require another style hammer.

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: My custom Norinco
« Reply #2 on: October 26, 2012, 12:32:14 PM »
Here is mine with new stocks.
Blessings
TEXAS, by GOD

Offline 1911crazy

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4793
  • Gender: Male
Re: My custom Norinco
« Reply #3 on: October 30, 2012, 09:26:05 AM »
My norc build is my best 1911 so far. She's pretty much a low end race 1911 operation wise.  I wish these were still $300 used but lately we can't touch the cost of the used ones. This norc 1911 had a loose barrel bushing in the slide.  It was more loose in the slide than on the barrel.
My norc build;
1. Used chinese norinco 1911a1 pistol in 45acp $300
2. New USGI 45acp/5" barrel from sportsmans guide $59
3. Two piece full length guide rod kit w/18# recoil spring  on sale at SPG  $9
4. IAI national match barrel bushing from CDNN investments  $12
5. IAI full wrap around rubber grips from CDNN  $8
6. Adjustable trigger CDNN $15
7. Ramped the disconnector, fitted the NM barrel bushing to the slide,  fitted the barrel to the NM barrel bushing for 100% loc-up, Checked the lugs in the full battery position for engagement with no barrel spring in full battery and in the lowered position when it loads the next round. Polish the feed ramp and throat the barrel.
8. Lubed with moly.
To this point thats my total cost with me doing all the work and fitting.  She shoots one clover leaf per 8rd mag no matter who shoots it.  Thats with a loose slide to frame fit too. I just wanted to see how good a bargain basement build could be with accuracy. For a total of $403 + or - it came out pretty good.  I'm not sure how long the cheaper parts will last but right now she shoots and cycles awesome. This accuracy is with the russian wolf 45acp ball ammo.
My next move would be to tight up the frame rail to slide fit a tad.
 

Offline yellowtail3

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5664
  • Gender: Male
  • Oh father of the four winds, fill my sails!
Re: My custom Norinco
« Reply #4 on: October 30, 2012, 11:54:33 AM »
I used to have a Norinco 1911, and I dearly regret selling it... even if I did make money on it.
Jesus said we should treat other as we'd want to be treated... and he didn't qualify that by their party affiliation, race, or even if they're of diff religion.

Offline jaysouth

  • Trade Count: (3)
  • Member
  • *
  • Posts: 55
Re: My custom Norinco
« Reply #5 on: October 30, 2012, 03:50:20 PM »
Jay - looks good, howz she shoot?  GI memory pad beavertail?  Not so sure if anyone makes those - lots of other style beavertails with memory pads but those most often require another style hammer.
Mikey,
She shoots better than I can hold her.  A beavertail works if you cut off a couple of serrations on the GI style hammer, but I have too much in this hammer to cut on it.  I have tried to build a GI style beavertail up with epoxy but it's not durable.  I had a friend TIG a memory pad on a GI grip safety.  It would not take bluing and cera coating.  The result felt OK but looked horrible.  My filing and shaping were not the best either.
I may have two or three tigged up and fitted so I can keep a black one on the gun at all  times.  Or, gasp, disable the thing.

Offline Mikey

  • GBO Supporter
  • Moderator
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 8734
Re: My custom Norinco
« Reply #6 on: October 31, 2012, 01:36:53 AM »
Oh Lordy:  the trials and tribulations we shooters go through to get the perfect pistol, but in the end.........

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: My custom Norinco
« Reply #7 on: November 04, 2012, 10:30:11 AM »
But in the end we still want to do something else to them or another. :o ::) ::) 8)
Blessings
TEXAS, by GOD

Offline midwayraider

  • Trade Count: (39)
  • Contributor
  • ***
  • Posts: 306
  • Gender: Male
  • 8-pointer on 11-04-09
Re: My custom Norinco
« Reply #8 on: November 04, 2012, 12:52:08 PM »
williamlayton .... where did you get those stocks for your norinco ? i also have a norinco and i would like to have a set of them .
kelly

Offline Mike in Virginia

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1551
Re: My custom Norinco
« Reply #9 on: November 12, 2012, 01:14:22 PM »
I've never heard anything negative about a Norinco.  Had one myself at one time.  I'd be interested to know if anyone ever got really serious about accuracy and tested one off sandbags at 25 yards?  I didn't do that with mine.  A beginning shooter in those early days. 
So many gun articles these days report the accuracy at lesser distances, and even by non-supported shooting.  I don't think we can get a real impression of a pistol's potential until it's fired from a rest at a full 25 yards.  The writer's reasoning is always that the weapon is for self defense, and 25 yards is not a reasonable test for a belt gun.  I think they simply won't shoot them that far because they know the result would not be favorable to the article.  I don't own any pistils or revolvers that haven't been sandbagged at 25 yards.  I suppose it's not that important for a belly gun, but I still like to know.  If the shooter is already at the range, it just takes a few minutes.  When I see the articles testin guns at shorter distances, I decide quickly that's not the gun for me.  The promoter is hiding something. 
You know what else galls my butt?  "Professional" shooters making videos of a pistols shooting characteristics.  I've seen the famous "Hickcock" on Youtube do that very thing.  Invaribly, they empty the magazine at their target and then flinch for that last trigger pull when the slide is back and the weapon empty.  Not only did they not count their rounds (a very basic procedure for all knowledgable shooters), but they actually flinched.  Therein lies another reason they don't test at 25 yards; they wouldn't be able to hit the paper. 
We can take that further.  If a policeman on the street has not had it drilled into him a thousand times at the range to count his rounds, he will lose the time he wasted in squeezing the trigger on a slide-back empty gun.  They all know better.  But the majority of videos we watch will show quickly that we've wasted our time clicking on that link.  One more point: Tactical reloading--if a shooter does not know how many rounds, he can't know whether a tactical reaload is called for.  A shooting incident might have it a lull--a lull that gives the officer time to insert a full magazine.  He drops the partially used magazine into his hand, then inserts a full one.  When the lull is over, he's back in the game with a fully loaded weapon, and he knows the number of extra rounds in the magazine he just dropped.  A minor thing, maybe, but it might make all the difference before the conflict is over.
I learned a similar drill with an 870 pump.  You'be been fighting, and your shotgun is dry.  The slide is back and the loading port open.  Load that first round by cupping the shell in your right hand and bringing it over the receiver to fall into the port.  Slam it home.  You've now one more instantly loaded round to save you.  Plus, if there's time to reload the convential way, you can push them in knowing all the time that you have that one round ready to go.  The opposite of that is to load an empty pump gun conventionally, by just shoving them through the gate.  The folley of that is you have nothing in the pipe until you jack it in.  Small things.  Things that save fractions of seconds.     
 
 

Offline williamlayton

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 15415
Re: My custom Norinco
« Reply #10 on: November 13, 2012, 02:08:21 AM »
Mideway
Those are from my favorite supplier of porn stocks from Esmeralda.
I have others from her.
Blessings
TEXAS, by GOD

Offline 1911crazy

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4793
  • Gender: Male
Re: My custom Norinco
« Reply #11 on: November 17, 2012, 06:43:32 AM »
Since my norc is shooting so decent i may not touch the frame rail fit as advised here by so many of you guys.  I may leave it like it is and enjoy it.  As most do its time to move to something else and play again.
I been thinking of purchasing more AGI gunsmith dvd's to learn more about S&W revolvers next.