« previous next »
Pages: [1]   Go Down

Author Topic: Sight Hood for this?  (Read 903 times)

0 Members and 1 Guest are viewing this topic.

Offline parisite

  • Trade Count: (3)
  • Member
  • *
  • Posts: 75
  • Gender: Male
Sight Hood for this?
« on: March 03, 2013, 05:43:37 AM »
Does FA make a sight hood for this particular front sight? Would really like to have one. One reason is for the sight picture and the other is to protect the sight itself.
 
Thanks...........
 
Logged
Friends don't let friends buy BSA scopes.

Offline benny123

  • GBO Supporter
  • Trade Count: (2)
  • Avid Poster
  • *****
  • Posts: 129
Re: Sight Hood for this?
« Reply #1 on: March 03, 2013, 06:37:22 AM »
I have the patridge front sight blade. They're no longer available, officially, through FA

Pretty sure they were used on the 353s and similar models that were silhouette oriented. I used to have a 10" 252, now sold, that had the comp rear and hooded front sight.
That front sight hood accommodated a much smaller front sight post.

I'm certain that hood would not fit your patridge, esp as your sight height looks like a .480 --which is typical 6". Just too tall

Of course you could always get the hooded site from FA,  but that kinda goes without saying I guess
Logged

Offline parisite

  • Trade Count: (3)
  • Member
  • *
  • Posts: 75
  • Gender: Male
Re: Sight Hood for this?
« Reply #2 on: March 04, 2013, 12:09:32 PM »
I was afraid my front sight would be too tall for the hood. The sight pictured is on a 10" 44 Magnum manufactured in 1990, so says FA. I bought it used at a great price.
 
So far I have been careful not to ding up the sight and I guess I will continue to do so.
 
If I was to elect to get the hooded front sight, are the hoods plastic or metal?
Logged
Friends don't let friends buy BSA scopes.

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Sight Hood for this?
« Reply #3 on: March 19, 2013, 11:21:12 AM »
A craftsman could make up one of some tubing that slides over the barrel/sight and a latch; there were such things in the past for target rifles. The basic version was the Springfield '03 sight hood if you want to search pics online for an idea of what I mean.
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline Richard P

  • Trade Count: (7)
  • Contributor
  • ***
  • Posts: 341
  • Gender: Male
Re: Sight Hood for this?
« Reply #4 on: March 20, 2013, 05:45:17 AM »
The one I have replaces the original front sight. It is covered and uses an adjustable post. It is on a M83 44m.  Perhaps Ken Light may help. See www.ihmsa.org  and ask on the forum.  rp
Logged

Offline Ken ONeill

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1259
  • Gender: Male
Re: Sight Hood for this?
« Reply #5 on: March 26, 2013, 02:55:44 AM »
The FA hoods are a matte black metal, probably aluminum.
Before FA offered the current adjustable front sight, they made two severely undercut ones like the one pictured. One was intended for use with a hood. That one had a notch cut at the bottom rear of the sight. When the sight was tightened it held the hood in place.
I can't see such a notch just above the sight base in your picture.
The sight hoods won't work with a holster.
Logged
Pages: [1]   Go Up
« previous next »