« previous next »
Pages: [1]   Go Down

Author Topic: Damp patch between shots  (Read 1356 times)

0 Members and 1 Guest are viewing this topic.

Offline Stuart C.

  • Trade Count: (5)
  • Contributor
  • ***
  • Posts: 305
  • Gender: Male
Damp patch between shots
« on: May 06, 2013, 09:06:29 AM »
Hi all,
 
If you have to wipe between shots like I do, what do you put on the patches between shots? I've seen recipes for lube "1 part a water-soluable oil, and 10 parts water." 
What's is a good readily avialable 'water soluable oil'?
 
Thanks!
 
Logged

Offline John Boy

  • Moderator
  • Trade Count: (0)
  • Contributor
  • *****
  • Posts: 381
Re: Damp patch between shots
« Reply #1 on: May 06, 2013, 03:45:34 PM »
Stuart, this is the results of cleaning a bore after 50 consecutive shots with no patching or blow tubing ...

* One cotton ball with plain water
* Three dry cotton balls
Water has been used for decades to clean the potassium bicarbonate and a trace of potassium sulfide foul in bores.  I wouldn't be concerned at all trying to find a water solvable oil to mix with water to clean bores
 
Logged
Regards
John Boy

Offline Ranch13

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1062
  • Gender: Male
    • Historic Shooting .com
Re: Damp patch between shots
« Reply #2 on: May 06, 2013, 04:52:05 PM »
Most that use the water soluble oil use the stuff available from NAPA parts.
I use 50-50 water and rv antifreeze, some use regular antifreeze.
 The main thing is to leave the bore in the same condition shot after shot.
Keep in your mind also that "wet" spots can create leading
Logged
In the 1920's "sheeple" was a term coined by the National Socialist Party in Germany to describe people that would not vote for Hitler. In the 1930's they held Hitler as the only one that would bring pride back to Germany and bring the budget and economy back.....

Offline darkgael

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1655
  • The readiness is all. 4049 posts from the “old” gb
Re: Damp patch between shots
« Reply #3 on: May 09, 2013, 12:35:23 AM »
Between shots at the range  with either a BPCR or any of my MLers, I run a patch lightly soaked with denatured alcohol (not rubbing alcohol). The alcohol evaporates rapidly and leaves the bore dry.
Pete
Logged

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Re: Damp patch between shots
« Reply #4 on: May 11, 2013, 02:40:25 AM »
Ballistol and water, about 1:10.  Damp side, flip it over, and dry side.
Logged
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline Cleburne

  • Trade Count: (10)
  • Contributor
  • ***
  • Posts: 270
  • Gender: Male
Re: Damp patch between shots
« Reply #5 on: May 23, 2013, 06:51:45 PM »
Quote from: Nobade on May 11, 2013, 02:40:25 AM
Ballistol and water, about 1:10.  Damp side, flip it over, and dry side.

+1
Logged
Pages: [1]   Go Up
« previous next »