« previous next »
Pages: [1]   Go Down

Author Topic: Round ball 45 70  (Read 2272 times)

0 Members and 1 Guest are viewing this topic.

Offline Spokerider

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 144
Round ball 45 70
« on: June 05, 2013, 04:50:35 AM »
I cast up some .490 pure lead balls for the contender 45 70, sized them first to .462 ......yes, it was a grunt, and then down to .459  ........much easier. Lubed with Lee liquid alox.
 
Now for powder.........Unique? Bullseye? What are you using? Is Bullseye position sensitive?
 
The idea is to have a plinking load that comes as close to the peep sight settings that I have adjusted for the 360gr hunting load. If I can`t get the POI close, even with titrating the powder charge, then the plan was a bust. It would be nice to have a plinking / small game load for in the field for shooting small game or varmints that hits reasonably close to the POI at 25m.
 
Anyone done this?
Logged

Offline wolverine_1

  • Trade Count: (3)
  • Contributor
  • ***
  • Posts: 364
  • Gender: Male
Re: Round ball 45 70
« Reply #1 on: June 05, 2013, 04:58:16 AM »
Years ago I loaded some swaged round balls in .45-70 cases over 5gr of Unique and shot some Artic Hare.  Very effective at about 50 yards.  They didn't even kick when hit.
Logged
Gene

Offline BBF

  • GBO Supporter
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 10042
  • Gender: Male
  • I feel much better now knowing it will get worse.
Re: Round ball 45 70
« Reply #2 on: June 05, 2013, 09:58:13 AM »
How do you keep them from going all the way down into the case?
Logged
What is the point of Life if you can't have fun.

Offline wolverine_1

  • Trade Count: (3)
  • Contributor
  • ***
  • Posts: 364
  • Gender: Male
Re: Round ball 45 70
« Reply #3 on: June 05, 2013, 10:12:22 AM »
They were slightly oversized.  That's 30+ years ago, so I don't remember the exact dia., but they just fit the case slightly below the center of the ball.
Logged
Gene

Offline GH1

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 939
  • Gender: Male
Re: Round ball 45 70
« Reply #4 on: June 08, 2013, 01:11:56 AM »
If it were me I'd use Trail Boss, it's designed for such applications.
GH1 :)
Logged
I owe my life to an organ donor

Offline gcrank1

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 7644
  • Gender: Male
Re: Round ball 45 70
« Reply #5 on: June 15, 2013, 05:46:23 AM »
With any fast powder taking up so little space I would lift the muzzle to settle it back to the primer, and I WILL NOT use any over-powder wad to hold such in position ever again.
Unique, Red Dot, Bullseye and Trail Boss are all in my inventory and I would try any of them. I would press the ball flush to the case mouth and smear a ring of a stiffish lube in the recess.
As to POI...... only one way to find out if it will be close enough for your needs, but it is easy enough to trial.
Logged
"Halt while I adjust my accoutrements!"
      ><   ->
We are only temporary caretakers of the past heading toward an uncertain future
22Mag UV / 22LR  Sportster
357Mag Schuetzen Special
45-70  SS Ultra Hunter with UV cin.lam. wood
12ga. 'Ol' Ugly OverKill', Buck barrel c/w  SpeedStock  and swap 28" x Full bird barrel, 1974

Offline GroovyMike

  • Trade Count: (0)
  • Member
  • *
  • Posts: 5
Re: Round ball 45 70
« Reply #6 on: November 04, 2020, 05:53:18 AM »
Trail boss powder would be a good choice but I use 25g of H322 behind a 405 grain bullet as my plinker loads.
Logged

Offline geezerbiker

  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 1884
  • Gender: Male
Re: Round ball 45 70
« Reply #7 on: November 13, 2020, 10:27:55 PM »
I loaded some up using Red Dot awhile back.  I don't remember the load I was using but they shot tight groups from my Handi rifle. 

Another load I liked was a cast 220g .452" bullet for the .45acp Teflon tape patched up to .459 and loaded over Unique but I don't remember how much.  I seem to recall less than 10g of unique but don't try it unless you look it up.

I've been wanting one of the Lyman collar button molds for a long time but they never seem to be in stock when I have the money.

Tony
Logged

Offline orerancher

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1103
Re: Round ball 45 70
« Reply #8 on: November 16, 2020, 10:26:57 AM »
Quote from: geezerbiker on November 13, 2020, 10:27:55 PM
I loaded some up using Red Dot awhile back.  I don't remember the load I was using but they shot tight groups from my Handi rifle. 

Another load I liked was a cast 220g .452" bullet for the .45acp Teflon tape patched up to .459 and loaded over Unique but I don't remember how much.  I seem to recall less than 10g of unique but don't try it unless you look it up.

I've been wanting one of the Lyman collar button molds for a long time but they never seem to be in stock when I have the money.

Tony

NOE, usually has the Collar button molds....
Logged

Offline geezerbiker

  • Trade Count: (14)
  • Senior Member
  • *****
  • Posts: 1884
  • Gender: Male
Re: Round ball 45 70
« Reply #9 on: December 02, 2020, 08:43:49 PM »
I've been tight on funds for a long time or I would have that mold and a few others I want... 

Tony
Logged
Pages: [1]   Go Up
« previous next »