Author Topic: Blr with non-glossy stock  (Read 1270 times)

0 Members and 1 Guest are viewing this topic.

Offline shooter

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 337
  • Gender: Male
Blr with non-glossy stock
« on: January 15, 2003, 06:44:56 PM »
Does browning make a gun without a high-gloss finish.I had a a-bolt micro medallion in 300 wsm...took it back-too glossy
Shooter

Offline southern utah

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 470
    • http://www.jsi-guns-hunting-firearms.com
BLR
« Reply #1 on: January 15, 2003, 07:12:25 PM »
They are know for there high gloss tough finish. There are a few that have sanded off the finish but it is a real hard finish.  Pretty though.

Offline CJ

  • Trade Count: (3)
  • Contributor
  • ***
  • Posts: 294
Blr with non-glossy stock
« Reply #2 on: January 16, 2003, 04:19:45 AM »
I used 0000 teel wool wet on mine, not enough to take the finish off, just enough rubbing to kill the shine. Now its kinda semi gloss.
NRA Lifer

Offline Bullseye

  • Trade Count: (9)
  • Senior Member
  • *****
  • Posts: 1879
Blr with non-glossy stock
« Reply #3 on: January 16, 2003, 05:02:30 PM »
My gosh CJ, you ruined a perfectly good finish.  Seriously, just kidding.  Everyone has their preference.  For what a Browning cost though, I am not sure I could pick up enough nerve to use that steel wool.

Offline shooter

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 337
  • Gender: Male
guess i wont buy a browning then
« Reply #4 on: January 16, 2003, 06:01:29 PM »
oh well,dont like them wooden airplane signal mirrors.Why spend the extra money for a browning and cover it with something just to hunt.Seems to me they should offer an alternative.I'd buy a BLR if it werent so darn shiny. :rain:
Shooter

Offline 45LC-Man

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 133
Blr with non-glossy stock
« Reply #5 on: January 17, 2003, 03:02:49 PM »
Acetone will take the shine off and leave the finish intact

Offline Lee D.

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 164
Blr with non-glossy stock
« Reply #6 on: January 18, 2003, 01:18:25 PM »
I also did the steel wool trick.  Any gun I get with that glassy finish gets a rub down.  Cuts the glare and does not require refinishing.  Start some place not very visble and rub until you get what you like.
somewhere betwixt a baulk and a breakdown

Offline Lee

  • Trade Count: (0)
  • Member
  • *
  • Posts: 40
Shooter, I dont worry about finish, here is why
« Reply #7 on: January 19, 2003, 10:38:19 AM »
First,  I dont think a deer pays much attention, especially if you are not
moving,  I think a deer will more likely see your face if you turn your head in a dark woods.  Also the butt end is tucked under your arm.

When hunting in  bright sunlight and in the open I see light flash from
the barrels of rifles.  that usually occurs when a hunter shifts his rifle from his hands to his shoulder or changes his grip and waves the muzzle around.  Most times you dont see a flash if a man does not wave his rifle around.  As for the stock, I never see a flash from that.

If you are allways stalking, and a good stalker who can stalk in close
then I might be concerned.  If that was the case I would just wind
electrical tape around the back end or make some other temporary
change using tape.

I use a BLR and the deer dont seem to notice but my range is usually
around 70 yards or more.  At 25 yards or less is when I would guess a deer could notice an un natural brightness.  

Just my 2 cents but I dont worry about such things

Lee

Offline shooter

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 337
  • Gender: Male
glare off stock
« Reply #8 on: January 19, 2003, 05:53:51 PM »
i just remember using a shiny 700 bdl and seeing a reflection on a nearby tree,couldnt figure out what was causing it at 1st,not my watch crystal.Turns out it was my rifle stock....just like signling a plane.
                                                                                   Shooter
Shooter

Offline MinnesotaJoel

  • Trade Count: (0)
  • Member
  • *
  • Posts: 42
Blr with non-glossy stock
« Reply #9 on: February 02, 2003, 10:33:58 PM »
When i bought my BLR, i talked to my grandpa about the glossy finish of the stock to my grandpa, mentioned to him that i might try to strip it down to look like the old Marlin .32ws he gave me (gorgeous gun) and maybe do some checkering on it.  He asked to borrow it a little ways before christmas and returned it to me, stripped, rubbed down with a waterproof brown shoe polish and checkered, exactly like my Marlin.  It is beautiful, and the most amazing thing?  He does his checkering with a pocket knife, and working in gun sales and custom building, i can tell you, it is flawless.  He never ceases to amaze me.
"The eye is the most sensitive part on a bear, if you want to keep you arm, Dave, touch his eye with that .44 sized hole in your barrel."

"Copenhagen Black...bourban flavored chew, best of both worlds."

Offline coug2wolfs

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 214
    • http://www.coug2wolfs.com
Blr with non-glossy stock
« Reply #10 on: February 03, 2003, 08:24:22 AM »
Guess one can look at it two ways  :wink:

My Bro-In-Law squealed like a stuck hawg about the stainless barrel on his Wby UL in -06.  Like I told him, deer don't know stainless from high carbon or copper.  But he had this affliction about it shining and scarin the critters and I ended up with it at a VERY good price!

Deer and just about any game animal run from movement and scent. More often than not, a flash is apt to lock them up as they will be curious to find out what it is.  Maty be just the time you need to slap em with a good bullet.


Best Regards,
Coug
AOL IM coug2wolfs

Life is a Journey, not a Destination.  Take the time to enjoy the gifts of the Great Spirit along the way.