« previous next »
Pages: [1]   Go Down

Author Topic: What rifle action for project???  (Read 978 times)

0 Members and 1 Guest are viewing this topic.

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
What rifle action for project???
« on: November 02, 2004, 01:21:42 PM »
I am looking for a mauser or other rifle action that will be good for a project. I enjoy tinkering and would like to do some gunsmithing.

Would like to find an action, strip it of the barrel, get an after-market barrel, stock, trigger, etc. Calibers I have in mind are 17Ackley Hornet, or another 17 cal, or 6.5-284, 6.5-06, or ??? Rechambering is no problem. If all goes well, I will get a shilen barrel after the tinkering.

As far as stocks, I would like a near drop-in where I could do some minor work and glass bed it.

Oh yeah...just like everyone else, I want the action at a reasonable price.

Thanks,
Kyle
Logged

Offline Mikey

  • GBO Supporter
  • Moderators
  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 8734
What rifle action for project???
« Reply #1 on: November 03, 2004, 04:24:15 AM »
The 98 Mauser is a good action - you can find actions only or barrelled actions and/or, the complete rifle for under $100.  The Shotgun news just had an add for VZ-24 Check Mausers for under $100.  

Another action you might wish to consider, albeit a bit heavier than the Mauser, is the P-14/M17 action - these were in British 303 or 30-06 caliber, respectively.  

I don't know what the pressures run to in the Hornet loads you referenced but I believe the 6.5- 06, etc., may run at too high pressures for the SMLE action, unless you get one of the Indian made 308s.  

There is also the option of finding an older Remington with a shot out barrel and using that as your platform.  Same for Winchester.  HTH.  Mikey.
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
What rifle action for project???
« Reply #2 on: November 03, 2004, 05:08:25 AM »
Altering any mauser to a hornet would be a real chore.  Getting it to actually feed ammo from a magazine will be worse..  Perhaps starting with a barreled action may be the best way to go..  The CZ rifles are really well built and usually very accurate..  Fitting a barrel to an action is not really tinkering, it's a delicate task that requires some speccialized tools...  The tooling is expensive to buy and not really cheap, to rent!!  Start with a barreled action and learn stocking first.  The metal work will come later..
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #3 on: November 03, 2004, 05:56:45 AM »
Gunnut,

I have done the stock work before.  Metalwork is where I am moving.  Caliber is not set in stone.  I will be fine with using a .473 base caliber.  Access to tooling is not a problem and will have a prof gunsmith looking on.

I am also not opposed to having a premade mauser barrel put on.  

Kyle
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
What rifle action for project???
« Reply #4 on: November 03, 2004, 08:03:43 PM »
The vz 98's are good actions and it is still possible to get into a Turkish marked action for very little.  The turk I bought is most likely going to end up a 7x57 or a 358..  decisions decisions!!  The 35 Whelan is always a good caliber choice as is the 257 Roberts..  A 98 is nearly the ideal length for a 257 as the parent case was a 7x57...  Starting with a military action lets one experience a lot more customizing than starting with a modern barreled action.  Most premade barrels for the 98 are short chambered.  This allows barreling without the use of a lathe, in theory anyway..  Most still should have the choulder adjusted so the barrel tightens on the shoulder and the inner ring at the same time.. a lathe makes this a lot easier..  Why not go the whole way and make the sights and scope mounts also..  an interesting project..
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #5 on: November 04, 2004, 04:06:32 AM »
Gunnut,

I have found an action for $60....bare action.  Sounds good to me.  Will have to buy sight unseen but I am assured there have been no modification done.

The 257RobAI would be an interesting round for me.  Might consider it or just the 257Rob.

Hope to get thing moving soon so I will have it to work on after hunting season.

Kyle
Logged

Offline sgtt

  • Trade Count: (5)
  • A Real Regular
  • ****
  • Posts: 556
What rifle action for project???
« Reply #6 on: November 09, 2004, 08:10:23 PM »
When you say "bare action", does it include the bolt?
Logged
"Freedom, for some, is problematic.  It does not grant emancipation from responsibility."

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #7 on: November 10, 2004, 04:21:49 AM »
bolt included...sorry...bare meaning no barrel or wood.

Kyle
Logged

Offline sgtt

  • Trade Count: (5)
  • A Real Regular
  • ****
  • Posts: 556
What rifle action for project???
« Reply #8 on: November 10, 2004, 07:33:07 PM »
Sounds like a pretty square deal.  I wouldn't expect anything too pretty.  I have a 257 Rob. on a 98 platform.  Great gun.  I may, someday, convert it over to AI.  I like the "odd".  Right now it is the primary hunting rifle of my 16 yr. old daughter.  She loves it just the way it is, so, someday may never come.
Logged
"Freedom, for some, is problematic.  It does not grant emancipation from responsibility."

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #9 on: November 11, 2004, 03:43:06 AM »
Sgtt,

Also found a place that has VZ24 no wood no barrel for $34.50 then shipping and FFL.

That is not bad either.

Kyle
Logged

Offline springer222

  • Trade Count: (1)
  • Avid Poster
  • **
  • Posts: 191
What rifle action for project???
« Reply #10 on: November 11, 2004, 01:09:45 PM »
Is that 1 action for <35$ or do they have several for sale. At that price I would like to get my hands on some!
Logged

Offline mitchell

  • Trade Count: (8)
  • Senior Member
  • *****
  • Posts: 2067
  • Gender: Male
What rifle action for project???
« Reply #11 on: November 12, 2004, 04:30:04 AM »
what place is that i wouldlove to get my hands on one or two of them????
Logged
curiosity killed the cat , but i was lead suspect for a while

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #12 on: November 12, 2004, 06:08:34 AM »
Let me find the pamphlet again.  They had several fro sale at $34.50.

Kyle
Logged

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #13 on: November 12, 2004, 06:50:25 AM »
At work...cannot find the link.

Will have to do a search at home on Monday...gon hunting this weekend.

Kyle
Logged

Offline HKusp40

  • Trade Count: (0)
  • Posts: 2
I would like some as well.
« Reply #14 on: November 21, 2004, 07:50:24 AM »
Have you found the link yet
Logged

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #15 on: November 22, 2004, 09:46:23 AM »
HKusp40,

i have searched high and low and cannot find or think of who had them at $34.50....still have the link for the $60 though if you want it.  I will copy and paste in a moment.

Kyle
Logged

Offline 5Redman8

  • Trade Count: (4)
  • Contributor
  • ***
  • Posts: 265
"
« Reply #16 on: November 22, 2004, 10:05:58 AM »
Logged
Pages: [1]   Go Up
« previous next »