« previous next »
Pages: [1]   Go Down

Author Topic: fair price for trigger job, slicking the rails Springfield  (Read 730 times)

0 Members and 1 Guest are viewing this topic.

Offline swifty

  • Trade Count: (0)
  • Member
  • *
  • Posts: 73
fair price for trigger job, slicking the rails Springfield
« on: February 12, 2005, 02:11:05 PM »
I just bought a Springfield Armory 1911-A1 target- supposed to have a match barrel, ramp shines like its been polished and other goodies.
It has a hard trigger pull with a two stage travel.
I would like to get the trigger job done right 3.5 pound pull and slick up the rails so they are a bit smoother. Probably will loosen up after a few hundred rounds. It has adjustable sights with the little glow in the dark dots. It seems to be very accurate if I can control my wobble factor.
The trigger has a sharp edge and I would like to smooth over the sharp edge. I only have about 75 rounds with it.
Comments or suggestions to slick this gun up to be a bit smoother .
I has a MSRP of $1080 so its definatly a better grade gun.
Logged

Offline Savage

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4397
fair price for trigger job, slicking the ra
« Reply #1 on: February 13, 2005, 02:08:17 PM »
Wow! A $1100 dollar pistol that needs smithing right out of the box!! I'd give Springfield a call, Surely they'll make it right!
Savage
Logged
An appeaser is one who feeds the crocodile hoping it will eat him last,

Offline Dusty Miller

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2271
  • Gender: Male
fair price for trigger job, slicking the ra
« Reply #2 on: February 13, 2005, 08:51:22 PM »
I'm having a similar experience with the trigger on my $1100 Kimber!
Logged
When seconds mean life or death, the police are only minutes away!

Offline Doc Killpatient

  • Trade Count: (0)
  • Member
  • *
  • Posts: 22
fair price for trigger job, slicking the ra
« Reply #3 on: February 14, 2005, 06:39:21 PM »
Swifty, before you send that gun to a smith.  Shoot the heck out of it.  I have one and felt the same way about it.  I am now very happy with the way it "broke in".   I would not reccommend sending it anywhere but the range with lots of ammo.  After 800 to 1000 rounds, if ya still don't like the way it feels then have a smith do his magic.  I am quickly nearing the 2000 round mark in mine and it is smooth as silk.  My .02
Logged
You gonna do something or just stand there and bleed!

Offline swifty

  • Trade Count: (0)
  • Member
  • *
  • Posts: 73
fair price for a trigger job
« Reply #4 on: February 21, 2005, 02:37:39 PM »
Thanks folks for the replys.
I plan to shoot it a lot then evaluate.
Logged

Offline swifty

  • Trade Count: (0)
  • Member
  • *
  • Posts: 73
fair price for trigger job
« Reply #5 on: March 07, 2005, 02:29:13 PM »
I sent it back to sprinfield armory aftter talking to the customer service person. The trigger pull was rough, lots of creap and very inconsistent .
They were very understanding and said they will look it over.
Logged

Offline raw52

  • Trade Count: (0)
  • Member
  • *
  • Posts: 8
fair price for trigger job, slicking the ra
« Reply #6 on: March 08, 2005, 03:08:24 AM »
SWIFTY

Give us an UpDate when you get your Springfield back as to their customer service and repairs.

Sounds like you will have a fine shooter there.

Best of luck!

Rich
Logged

Offline rbwillnj

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 349
fair price for trigger job, slicking the ra
« Reply #7 on: March 08, 2005, 05:34:06 PM »
I have done any number of trigger jobs on my 45s, and I like to take them to a nice clean 3.5 lbs with no creep.  Even so, the feel of the trigger improves with with use.  Give it 500-1000 rounds.  

By the way, a 5 lb trigger with no creep is better than a 3 lb trigger with creep.
Logged
Pages: [1]   Go Up
« previous next »