Author Topic: Info/opinions please on lead pot  (Read 579 times)

0 Members and 1 Guest are viewing this topic.

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Info/opinions please on lead pot
« on: February 19, 2005, 04:08:45 AM »
Any opinions or info on a Lee Procuction Pot IV?. Do they have a temperature control? Is the system they use to control the lead flow good or not? Any other pots to be preferred instead of this pot for a fairly new (did it years ago though) bullet caster who does not do a lot of casting? What are they going for new? Whats a better pot in the same price range? Thanks....<><.... :grin:
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley

Offline rk4570

  • Trade Count: (0)
  • Member
  • *
  • Posts: 63
Lead pots
« Reply #1 on: February 19, 2005, 04:48:05 PM »
You can spend a LOT more $ but I think the Lee lead pots are great and Ive used one for several years.

I use the dipper model and kept it for a back up when I bought the Lyman but it burned out after a couple of years soooo I started using the Lee   and its still going!  :grin:
I spent a lot of money on Guns, Wild Horses & Wilder Women but I guess I just wasted all the rest!

Offline Leftoverdj

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1398
Info/opinions please on lead pot
« Reply #2 on: February 19, 2005, 06:31:55 PM »
The 20 lb pot is much better than the ten. They still have some dripping problems but much less than the tens. Some poster have reported adding a few ounces to the the valve rob and stopping the dripping.

Lee uses a heating element control rather than a true temperature control and the heat will creep up on you as the pot empties. Little experience and you can control that pretty good.

I'm satisfied with the value, but I am cheap.
It is the duty of the good citizen to love his country and hate his gubmint.

Offline Haywire Haywood

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1230
  • Gender: Male
Info/opinions please on lead pot
« Reply #3 on: February 20, 2005, 05:28:45 AM »
I have Lee's 10lb bottom pour and their 20lb ladel pot.  If you go bottom pour definately get the 20 pounder.  The valve works on the 10lb pot angle across the pot making it a pain to stir or add lead.  I use the ladel pot and a ladel with the spout drilled out to 3/32 for big bullets.  Dan at Mountain Molds said I'd get better fillout on lead hungry molds with it.

Ian
Kids that Hunt, Fish and Trap
Dont Steal, Deal, and Murder


usually...

Offline Rustyinfla

  • GBO Supporter
  • Trade Count: (4)
  • Senior Member
  • *****
  • Posts: 1744
Lee pot
« Reply #4 on: February 20, 2005, 09:50:51 AM »
I have one and I love it. The best thing about it IMHO is the slot in the top of the rod that fills the pour spout. My mallet that I use to cut the sprues with has been modified to hold a small screwdriver blade in the handle. If, while I'm pouring I should get a dribble the tool is already in hand to take care of the problem. I don't have to put anything down and look for the right tool.
  BTW my "mallet" is a straight piece of a broken pick handle.
                 Rusty <><
If you're gonna be stupid ya gotta be tuff

Offline sharps4590

  • Trade Count: (1)
  • Contributor
  • ***
  • Posts: 388
Info/opinions please on lead pot
« Reply #5 on: February 20, 2005, 03:03:53 PM »
I've had a Lee 10 lb. pot for over 20 years.  About 10 years ago I got the Lyman 20 lb. bottom pour and since then the Lee doesn't see much use except for revolver bullets.  

Mine has been good and as is typical of most Lee products I think it's a good buy for the money.  It isn't a Lyman, Saeco or RCBS but then it doesn't cost $225.00+ either.  The original thermostat on my Lee still works and I had to replace the one on my Lyman after about 5 years but it saw a heck of a lot of use in those 5 years also.

If you're casting big bullets, 400 gr.+, I would think you'd be happier with a 20 lb pot.  

Vic
NRA Patron, 2006
NRA Endowment, 1996
NRA Life, 1988
NAHC Life, 1985
There is no right way to do a wrong thing

Offline Robert

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1618
Info/opinions please on lead pot
« Reply #6 on: February 20, 2005, 03:24:44 PM »
The only problem with the Pro 20 is the amount of clearance underneath.  The IV has a lot more clearance....I do not know why the Pro 20 is made so much lower...I can't fit my core molds under it at all.  I went with the Pro 20 beacuse it fits my ingots (cookies).  I am thinking of modifying it, should be pretty easy to get some hardware and raise it up a little.  The base is just screwed on from the bottom.  Hey MSP..do you still need those spitzers?  I have been trying to find a little bit of tin so I can get them to flow a little nicer...remember I told you I had problems with the 280's turning out weird with the 1/2&1/2 mixture I was using....I HAVE NOT forgotten about you.
  I think you will be happy with the Pro 20.
....make it count

Offline jh45gun

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 4992
Info/opinions please on lead pot
« Reply #7 on: February 20, 2005, 05:57:27 PM »
I have one  a  Lee 10 # bottom pour and have had no problems some say they drip sometimes but this is the advice I gave at a other forum.

 "I have found that a paper clip or a small piece of wire shoved through the spout with a pair of pliers and wiggled around seems to clean out the hole and then using a screwdriver on the rod to twist it around seems to clean the spout and stop the drips for me. I have no problems with my  lead pot after doing this. Jim "
Said I never had much use for one, never said I didn't know how to use it.

Offline MSP Ret

  • GBO Supporter
  • Trade Count: (173)
  • Senior Member
  • *****
  • Posts: 8940
  • Gender: Male
Info/opinions please on lead pot
« Reply #8 on: February 21, 2005, 02:19:17 AM »
Thanks for all the replys guys, and Robert yes those bullets would be great, I have not given up on you!!!. The spitzers you spoke of, were those the .308/.309 fro the special run mold? I have the mold here but I thought you said you had one also. Was it you that had said he would mold up a bunch for me and another guy (I owe him) for the couple of boxes of GC's? I do remember you were going to send me some bullets for the scale parts but it's been a while and I have had so much going on I am probably mixing a couple of deals together. I do remember you were going to send me some bullets for the scale parts and I am hoping you were also the one who was willing to mold up some .30 cal spitzer cg's for the exchange of some cg's...now you have made my day, I was hoping to get some bullets in to load....Thanks....<><.... :grin:
"Giving up your gun to someone else on demand is called surrender. It means that you have given up your ability to protect yourself to a power that is greater than you." - David Yeagley