« previous next »
Pages: [1]   Go Down

Author Topic: Do you clean your Dies?  (Read 528 times)

0 Members and 1 Guest are viewing this topic.

Offline papajohn428

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 755
Do you clean your Dies?
« on: March 14, 2005, 01:57:07 PM »
And if you do, how?  I used to load a lot of lead SWC's in 357's, and the shaved lead and lube would gum up the seating die in a hundred rounds or so.  So I'd unscrew the die, take it apart, and ream out the core with a bore brush.  Since I only load plated and jacketed bullets these days, that problem is gone, but I look at my 20+ year old dies and wonder if they need a good bath.  Some have rusted from high humidity, or oily fingers.  Is there a need to clean them?  It's amazing the questions I come up with while I'm loading a batch of ammo..... :roll:

Papajohn
Logged
If you can shoot home invaders, why can't you shoot Homeland Invaders?

Offline Catfish

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 2696
Do you clean your Dies?
« Reply #1 on: March 14, 2005, 02:51:00 PM »
Like you, the only dies I clean are those that load cast bullets. I have no trouble cleaning them though, as I use Dillon dies for all of my loading with cast bullets. With dillon dies you just pull the keeper pin on top of the die and shove down. What`s inside comes out the bottom were you just wipe the wax off, push the insides back in and snap on the keeper pin. You don`t even take themout of the press, whole job from start to finish abt. 2 min., if you take a couple dirnks of coffie while doing the job. Dillon dies cost abt. $50, but if your going to load cast bullets they are the cheapest thing you can do to speed up your loading.  8)
Logged

Offline Redhawk1

  • Life time NRA Supporter.
  • GBO Supporter
  • Trade Count: (78)
  • Senior Member
  • *****
  • Posts: 10748
  • Gender: Male
Do you clean your Dies?
« Reply #2 on: March 14, 2005, 06:42:34 PM »
I just pull the guts out and spray in some cleaner and run a dry patch in to remove the solvent and spray a light coat of break free in and run another dry patch in the die to remove any excess lube.  Sometimes I just use air from my compressor.  :D
Logged
If  you're going to make a hole, make it a big one.
ΜΟΛΩΝ ΛΑΒΕ
Only two defining forces have ever offered to die for you,
Jesus Christ and the American G. I.
One died for your soul, the other for your freedom

Endowment Life Member of the NRA
Life Member NA

Offline MickinColo

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 163
Do you clean your Dies?
« Reply #3 on: March 15, 2005, 01:33:08 PM »
I don’t clean my dies very often. When I clean dies I use a spray on gun cleaner like Quick Scrub cleaner/degreaser, I lube them with WD-40, blow them out with dry compressed air and let them dry.
Logged
Keep your powder dry and your flint sharp

Offline willysjeep134

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 362
Do you clean your Dies?
« Reply #4 on: March 16, 2005, 08:40:31 AM »
I had to clean some sticky grease out of a set of new dies with lighter fluid. I reload in an unheated workshop so sometimes I get case lube gunking up a die and I need to take it apart. I will swab it out with Qtips and let it dry by the furnace. Cold dies and lube don't go toghther, so I need to warm up the dies before I reload I guess.
Logged
If God wanted plastic stocks he would have made plastic trees.

Offline ricciardelli

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1004
  • Gender: Male
    • http://stevespages.com/page8.htm
Do you clean your Dies?
« Reply #5 on: March 16, 2005, 09:42:54 AM »
After every use.  

I don't disassemble them, I toss them in the ultrasonic cleaner for a few minutes, let them dry, and them put them back in their plastic boxes.
Logged

Offline razmuz

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 271
You Clean Dies ??
« Reply #6 on: March 17, 2005, 08:06:50 AM »
About every ten years or so, on a cold haven't got any thing else to do night, I take my dies all apart and run them through the dish washer.
Logged
Pages: [1]   Go Up
« previous next »