« previous next »
Pages: [1]   Go Down

Author Topic: Hello Mauser type action  (Read 607 times)

0 Members and 1 Guest are viewing this topic.

Offline nealglen37

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 130
Hello Mauser type action
« on: May 14, 2005, 10:34:46 AM »
I have a JC higgins model 50 270 rifle .........................it has a mauser type action...................its very accurate...................but I have to use pointed bullets....................if I try to put in a round nose shell it doesn't want to go into the barrel............................................the bolt pushes the bullet into the barrel after a little while.......but the tip is marred up..........it doesn't do this with pointed bullets.........any suggestions?

Thanks
Logged

Offline Gun Runner

  • Trade Count: (33)
  • Senior Member
  • *****
  • Posts: 1140
  • Gender: Male
Hello Mauser type action
« Reply #1 on: May 14, 2005, 12:21:44 PM »
I have the same exact rifle you have, but have neer tried RN bullets. Now you got me woundering and gonna have to pick up a box of them to find out.
Just for your info: these were the mauser 400 series actions and were assembled for sears by Hi-Standard. I got this info from Hi-Standard.
This is the second one I've owned and gonna keep this one.

Gun Runner
Logged

Offline Rogue Ram

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 356
Hello Mauser type action
« Reply #2 on: May 14, 2005, 03:43:46 PM »
Ditto to what Gun Runner said. I have the .30-06 version. Beats any factory gun out there today for overall quality. Never tried RN bullets in it though. Very accurate with Hornaday Light Mag ammo by the way.

RR
Logged

Offline tcman

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Hello Mauser type action
« Reply #3 on: May 14, 2005, 05:04:27 PM »
Get a COAL gauge unit and then you can get the right measurements to set your seating die at to avoid having the bullet engage the rifling.
Logged

Offline gunnut69

  • Moderators
  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 5005
Hello Mauser type action
« Reply #4 on: May 15, 2005, 07:06:01 AM »
I'm not positive but believe the bullet nose is hanging on the feed ramp or where the feed ramp overhangs the magazine box.  The round nose bullets are the worst as they have a lot of soft lead exposed on the tips.  Use a bent needle file or riffler to smooth and then polish the metal, either with sand paper (400-600 grit) or a moto tool.  Avoid removing too much metal..  It is also possible the feed lips are retaining the round a bit too long.  This I would reccommend go to a qualified gunsmith..
Logged
gunnut69--
The 2nd amendment to the constitution of the United States of America-
"A well regulated militia, being necessary to the security of a free state, the right of the people to keep and bear arms, shall not be infringed."

Offline Judson

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 241
Hello Mauser type action
« Reply #5 on: May 17, 2005, 01:25:34 PM »
That JC Mod 50 is in reality a commercial FN Mauser.   The problem you are running into could be the edges of the chamber.    If there is not enough radius here the exposed lead of the round nose bullet will catch and bite in.    More radius can be cut but this is a job for a gunsmith that knows what they are doing so be careful if this is the problem.    Gunnut may also be right however I have seen few commercial FNs that will not handle all ammo.
Logged
There is no such thing as over kill!!!!  :-)
Pages: [1]   Go Up
« previous next »