Author Topic: Plain Base vs. Bevel Base  (Read 1349 times)

0 Members and 1 Guest are viewing this topic.

Offline Lvl1trauma

  • Trade Count: (0)
  • Member
  • *
  • Posts: 65
Plain Base vs. Bevel Base
« on: February 27, 2003, 04:26:14 PM »
In the past I have cast a lot of gas check bullets for my revolvers. They shoot pretty good and I have had no problems. I am in the process of deciding on molds for my .45's. I can't decide on plain base vs. bevel base. It seems like somewhwere I have read that as a rule plain base causes less leading (?gas cutting) than bevel base bullets. Makes sense to me because of a better seal. Also, I have read that plain base bullets give better accuracy than bevel base- better seal = better accuracy/less fouling. What are yall's experiences?

Beau

Offline bumble

  • Trade Count: (0)
  • Member
  • *
  • Posts: 31
Plain Base vs. Bevel Base
« Reply #1 on: February 27, 2003, 04:52:00 PM »
The plain base have always given me less leading though not always the best groups.  The pistols I cast for now like the plain base.  Bevel base sure drop from a mould easier than the plain base do. I vote plain base.

Offline hubbard

  • Trade Count: (0)
  • Member
  • *
  • Posts: 50
Plain Base vs. Bevel Base
« Reply #2 on: February 28, 2003, 01:26:53 AM »
bevel bases make the bullets easier to start in the brass and really help with lead shaving. can't say they are more prone to lead  than a flat base but  they don't shoot as well in my guns as a plain base. i've never heard any of my friends, that cast, say they prefer bevel bases.

Offline Nobade

  • Trade Count: (2)
  • Senior Member
  • *****
  • Posts: 1927
Plain Base vs. Bevel Base
« Reply #3 on: February 28, 2003, 02:22:36 AM »
I vote for plain base. I've never gotten the accuracy from the bevel base designs that I can from the plain base ones. Even tried using a BB mould and cut the bevel out of it. Groups tightened up and leading was reduced. For the home caster I'd go with PB every time.
"Give me a lever long enough, and a place to stand, and I'll break the lever."

Offline Larry Gibson

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1069
Plain Base vs. Bevel Base
« Reply #4 on: February 28, 2003, 05:13:04 AM »
Quote from: Nobade
I vote for plain base. I've never gotten the accuracy from the bevel base designs that I can from the plain base ones. Even tried using a BB mould and cut the bevel out of it. Groups tightened up and leading was reduced. For the home caster I'd go with PB every time.


I've been shooting cast bullets for over 35 years.  Agree with Nobade 100+%.  Have run tests of Plain base vs bevel base numerous times with handguns and rifles.  The plain base always come out ahead.

Larry Gibson

Offline Lvl1trauma

  • Trade Count: (0)
  • Member
  • *
  • Posts: 65
Plain Base vs. Bevel Base
« Reply #5 on: February 28, 2003, 05:47:19 PM »
Thanks for all of the info, guys. That just validates what I already figured.

Beau

Offline sundogg1911

  • Trade Count: (0)
  • Member
  • *
  • Posts: 95
Plain Base vs. Bevel Base
« Reply #6 on: March 28, 2003, 04:30:29 PM »
I like bevel base for my 45's shooting a low velocity load for IPSC. They're easier to load...and I load a lot of 'em, but for accuracy plain base can't be beat

Offline dakotashooter2

  • Trade Count: (2)
  • A Real Regular
  • ****
  • Posts: 952
Plain Base vs. Bevel Base
« Reply #7 on: March 28, 2003, 07:04:36 PM »
3 revolvers and two autoloaders have led me to the same conclusion.
Just another worthless opinion!!

Offline pjh421

  • Trade Count: (0)
  • Member
  • *
  • Posts: 44
Plain Base vs. Bevel Base
« Reply #8 on: May 05, 2003, 08:29:31 PM »
I paid $135 for a 4 cav, 200grain H&G #68 mould.  I made sure to order a plain base design.

Paul

Offline Lvl1trauma

  • Trade Count: (0)
  • Member
  • *
  • Posts: 65
Plain Base vs. Bevel Base
« Reply #9 on: May 06, 2003, 05:02:28 PM »
As per this post, I did basically the same thing. I already had the RCBS 2-cavity mold but I recently bought a 4 cavity Saeco 69 which is a flat base number 68. I have cast several hundred but haven't lubed or shot them yet- waiting on the new old Star sizer from California. Got a feeling it is gonna be the best money ever spent.

Beau