« previous next »
Pages: [1]   Go Down

Author Topic: Need some help  (Read 716 times)

0 Members and 1 Guest are viewing this topic.

Offline Doc Lisenby

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Need some help
« on: November 14, 2005, 01:01:39 PM »
The local Sheriff's Office brought me a black powder rifle to unload because they had discovered that a ramrod could not be inserted fully into the barrel.  They asked if I had a percussion cap so they could shoot it in order to clear it before they took it into the court room.
I cautioned against such action because the load was unknown.
I have been a gunsmith for many years but my experience with black powder guns is limited.
The rifle is stamped as a Traditions Tracker 209 In-Line and as near as I can determine is about 50 cal.
I removed the breech plug and found that it had been loaded with three black powder/Pyrodex? pellets and two saboted 240 gar. 44 cal. soft nose bullets.
I need to know if it is a common practice to assemble such a load or if it might had been done in an attempt to booby trap this rifle?
Also, it this rifle designed to fire some special percussion cap.? I don't see any evidence of a nipple or provision to accept a shotgun primer.
Any information you can furnish will be greatly appreciated.  This rifle was presented as evidence in a drug raid.
Doc
Logged
Seen it all, done it all, can't remember most of it.

Offline savageT

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1594
Need some help
« Reply #1 on: November 14, 2005, 01:38:19 PM »
Doc,
No I doubt if someone intentionally loaded two sabots/bullets on top of three pyrodex or triple 7 pellets.  These guns can take a 150 grain load (3-pellets) of black powder substitute.

Contact Traditions if you need more info.......
http://www.traditionsfirearms.com/eshop/10Browse.asp?Category=Muzzleloaders%3A+Tracker+209+%28In+Lines%29

Jim
Logged
savageT........Have you hugged a '99 lately?

Of all the things I've lost in my life, I miss my mind the most.

Offline Redhawk1

  • Life time NRA Supporter.
  • GBO Supporter
  • Trade Count: (78)
  • Senior Member
  • *****
  • Posts: 10748
  • Gender: Male
Need some help
« Reply #2 on: November 14, 2005, 05:06:50 PM »
Good thing you checked it out, sounds like a accident waiting to happen.  :eek:
Logged
If  you're going to make a hole, make it a big one.
ΜΟΛΩΝ ΛΑΒΕ
Only two defining forces have ever offered to die for you,
Jesus Christ and the American G. I.
One died for your soul, the other for your freedom

Endowment Life Member of the NRA
Life Member NA

Offline sheephunterab

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 147
Need some help
« Reply #3 on: November 14, 2005, 07:57:52 PM »
The rifle likely uses a 209 shotgun primer for ignition.

The powder sounds right but two bullets is a recipe for disaster. It's a very good thing you did not fire it.
Logged

Offline dispatch 510

  • Trade Count: (0)
  • Member
  • *
  • Posts: 77
Need some help
« Reply #4 on: November 15, 2005, 04:07:46 AM »
I have learned to check,I bought a T/C Renegade and a T/C Greyhawk about 7 months apart but from the same pawn shop and both of them were loaded.
Logged

Offline Doc Lisenby

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Need some help
« Reply #5 on: November 16, 2005, 10:25:06 AM »
Thanks all.  It was relatively easy to unload this rifle, but I wonder how to unload a rifle which has been loaded with saboted rounds which doesn't have a removeable breech plug?  I know about using the bullet screw to pull a lead  bullet out, but with a jacketed bullet, this wouldn't be an easy task. I also know about the nipple pneumatic tool to force the load out with compressed air.  Are there other methods?
Doc
Logged
Seen it all, done it all, can't remember most of it.

Offline Redhawk1

  • Life time NRA Supporter.
  • GBO Supporter
  • Trade Count: (78)
  • Senior Member
  • *****
  • Posts: 10748
  • Gender: Male
Need some help
« Reply #6 on: November 17, 2005, 01:28:33 AM »
I have removed the nipple and used my compressor with the blower with a rubber tip. It is regulated at 30 psi. Just point the gun in a safe direction. Works all the time.  :D
Logged
If  you're going to make a hole, make it a big one.
ΜΟΛΩΝ ΛΑΒΕ
Only two defining forces have ever offered to die for you,
Jesus Christ and the American G. I.
One died for your soul, the other for your freedom

Endowment Life Member of the NRA
Life Member NA

Offline Keith Lewis

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 804
Need some help
« Reply #7 on: November 18, 2005, 08:14:38 AM »
I have heard of using a grease fitting in place of the nipple and using a grease gun to force the charge out with grease. Seems like a messy method to me but it is different. Not sure where you find grease fittings with same threads as the nipples.
Logged

Offline Doc Lisenby

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Need some help
« Reply #8 on: November 20, 2005, 02:45:12 AM »
Yeah, I can see a problem there.  There are several different nipples which are not interchangeable.  I believe that grease fittings are pretty well standardized but come in different sizes.
I have seen the rubber tipped air tools somewhere but seems like they were for a specialized task.  I've never seen them as a tool market item.
I can just about bet that if I don't get one, I will need one eventually. Any ideas about where to look?
Logged
Seen it all, done it all, can't remember most of it.

Offline DanielWGriggs

  • Trade Count: (0)
  • Contributor
  • ***
  • Posts: 317
Need some help
« Reply #9 on: November 20, 2005, 02:56:30 AM »
got mine at Ace hardware. See the metal tipped ones most of the time.
Logged

Offline Doc Lisenby

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Need some help
« Reply #10 on: November 20, 2005, 04:09:24 AM »
Thanks Dan.  I'll give them a try tomorrow.
Logged
Seen it all, done it all, can't remember most of it.

Offline Keith Lewis

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 804
Need some help
« Reply #11 on: November 20, 2005, 04:49:05 AM »
Harbor Freight Tools sells complete nozzle ends with the trigger assembly cheaper than most have the ends only. If you have a Harbor Freight Tool close you could check there. I just got a complete assembly with an long 20 inch extension and a rubber tip for $2.00.
Logged

Offline Doc Lisenby

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 119
Need some help
« Reply #12 on: November 20, 2005, 06:10:31 AM »
So Harbor Freight  finally has something I can use.  That is a real good deal.  My local hardware charges that much for a rubber gasket/seal.
Thanks.
Logged
Seen it all, done it all, can't remember most of it.
Pages: [1]   Go Up
« previous next »