« previous next »
Pages: [1]   Go Down

Author Topic: 6.8 Rem for Contender  (Read 1012 times)

0 Members and 1 Guest are viewing this topic.

Offline Turk1961

  • Trade Count: (4)
  • Member
  • *
  • Posts: 73
6.8 Rem for Contender
« on: February 01, 2006, 07:27:31 AM »
Found some barrels listed as 6.8 Rem for the Contender.  I would think this new round would be too hot for the Contender.  Anybody know about this?  If it is not too hot, it would be a good choice for a young deer hunter.


Richard
Logged

Offline Special Ed

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 177
6.8 Rem for Contender
« Reply #1 on: February 01, 2006, 09:01:22 AM »
The 6.8 spc (Rem) is an excellent Contender cartridge. Low pressure & good velocity. Thompson is offering it in factory barrels, they would not offer something that wasn't safe.
If I lived where I could use it for Whitetail, I would buy one in a second.
From what I have seen here on GBO, there aren't to many people that are interested in it.
Ed
Logged

Offline jason280

  • Moderator
  • Trade Count: (7)
  • A Real Regular
  • *****
  • Posts: 539
6.8 Rem for Contender
« Reply #2 on: February 01, 2006, 10:23:32 AM »
I've been shooting one in an Encore, and its an excellent round.  Recoil is minimal, and accuracy has been pretty good.  Brass is finally becoming relatively cheap, and there are quite a few good bullets out there for it.  It should make an excellent whitetail round, which is what I plan on using it as next season.
Logged
"Hey Peter, check out Channel 9!!"

Offline Turk1961

  • Trade Count: (4)
  • Member
  • *
  • Posts: 73
6.8 Rem for Contender
« Reply #3 on: February 04, 2006, 08:46:02 AM »
Looked up the 6.8 mm Rem SPC in my new Hodgdon book and it shows some starting loads above 47000 and max loads up to 54000 PSI.  How much pressure can a Contender frame handle without damage?  If the frame can handle the 6.8mm R SPC pressure at 54000, why canÂ’t we use a lot of other rifle rounds?  

The 250-3000 Savage is said to be too hot for the Contender, but itÂ’s max pressures are less than 45000.  I just donÂ’t understand how it is too hot but a load at 20% higher pressure is OK.

Anybody know the answer?  I just don't understand this.
 :shock:

Richard
Logged

Offline Grumulkin

  • Trade Count: (33)
  • Senior Member
  • *****
  • Posts: 2028
    • http://www.orchardphoto.com
Contender Loads and Pressures
« Reply #4 on: February 04, 2006, 12:11:52 PM »
Part of the equation on how much pressure the Contender can handle has to do with the diameter of the cartridge.  A smaller diameter cartridge will leave more metal around it to contain the pressure than will a larger diameter cartridge.
Logged

Offline spinafish

  • Trade Count: (24)
  • Senior Member
  • *****
  • Posts: 1161
  • Gender: Male
6.8 Rem for Contender
« Reply #5 on: February 06, 2006, 05:07:45 AM »
I have one coming from T/C in exchange for a 16 1/4".414 Super Mag that couldn't be repaired.  Mine is going to be the 23" rifle barrel.  

Scrounging for loads now.  Midway has brass and loaded ammo.  Barnes has an excellent 100 grainer for the 6.8SPC (.277).
Logged
the most heartwreching words any man will ever hear
"depart from me, I never knew you"  Jesus
We may ignore, but we can nowhere evade the presence of God. The world is crowded with Him. He walks everywhere incognito.” C.S. Lewis

Offline skb2706

  • Trade Count: (5)
  • Senior Member
  • *****
  • Posts: 1428
6.8 Rem for Contender
« Reply #6 on: February 06, 2006, 09:12:59 AM »
Several factors to consider when setting pressure limits on the Contender.

Head diameter....6.8 is smaller head diameter than the .473" of the .250 Savage, .308 etc.

Shoulder angle ....if applicable, sharper reduces the back thrust or so the theory goes.

Backthrust is the common cause of frame stretching.
Logged

Offline panman

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 246
  • Gender: Male
6.8 Rem for Contender
« Reply #7 on: April 19, 2006, 02:25:13 AM »
Special Ed,i think that its not that many people are not intrested in the round, i think that its so new that many havent heard of it.I know i love mine so far.Im just waiting for some dies, and then i can share some load data.pan.
Logged

Offline Maine Woods

  • Trade Count: (0)
  • Avid Poster
  • **
  • Posts: 105
Re 6.8
« Reply #8 on: April 20, 2006, 02:31:38 AM »
Hi jason280 I am planning on useing the 6.8 spc for whitetail also. I first thought of it for my young nephew, but I am enjoying my thumbhole stock 23" bull barrel 17 HMR set up so much I may use it myself ( at least some of the time ! ) What bullet are you thinking of useing I can go factory ( of course :roll: ) or hand load. Thanks John.
Logged
Pages: [1]   Go Up
« previous next »