« previous next »
Pages: [1]   Go Down

Author Topic: Trigger work  (Read 535 times)

0 Members and 1 Guest are viewing this topic.

Offline Hunternz

  • GBO Supporter
  • Trade Count: (0)
  • Member
  • *****
  • Posts: 86
  • Gender: Male
Trigger work
« on: February 20, 2006, 10:22:03 PM »
Thanks to Raynors description of lightning the trigger I sucessfully lightened my trigger to 3 1/4lb,
Due to taking the three pins out at once I didn't see where the hammer spring lived and then I managed to jam the hammer against the barrel opening lever, so another pin out and another spring to sought out, due to my lack of mechanical skill it took me 4 hours to sought out how and why each part worked and where they went and which order they go back in :oops: , the good news is I know could do it all in whole less time and know how my H&R works :lol:
Regards Howard
Logged

Offline dodd3

  • Trade Count: (1)
  • Senior Member
  • *****
  • Posts: 1004
  • Gender: Male
Trigger work
« Reply #1 on: February 21, 2006, 12:27:48 AM »
here ya go howard this should help in the fewture.you might be best to print it.
bernie :D

http://www.e-gunparts.com/productschem.asp?chrMasterModel=1560z163
Logged
if its feral its in peril

Offline bucknbass

  • Trade Count: (2)
  • Member
  • *
  • Posts: 49
Trigger work
« Reply #2 on: February 21, 2006, 01:54:37 AM »
You can go here too.  He's a buddy ofmine and these are very precise instructions with pictures.

http://www.perkloafm.com/
Logged

Offline knight0334

  • Trade Count: (3)
  • Senior Member
  • *****
  • Posts: 1138
  • Gender: Male
    • Pennsylvania Firearm Owners
Trigger work
« Reply #3 on: February 21, 2006, 02:26:48 AM »
Thats some seriously detailed instructions on how to tune your Handi.

 :agree:   :agree:    :agree:    :agree:
Logged
RIP ~ Teeny: b.10/27/66 - d.07/03/07

Offline myarmor

  • Trade Count: (46)
  • Senior Member
  • *****
  • Posts: 3239
  • Gender: Male
Trigger work
« Reply #4 on: February 21, 2006, 02:51:14 AM »
Howard I know what you mean about getting the stinking thing back togather! Man the first time was a Pain in the A$$, but after you do it a couple times it does get easier thats for sure. The spring is what messed with me the most too :x  :)
Logged

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Trigger work
« Reply #5 on: February 21, 2006, 05:19:42 AM »
Perklo's instructions have always been in the FAQ, everyone needs to read the FAQ, you're missing a LOT of good info that applies to your Handis. Fred M has a section on triggers, also. :wink:

Tim
Logged
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Donaldo

  • Trade Count: (0)
  • A Real Regular
  • ****
  • Posts: 576
12 oz trigger
« Reply #6 on: February 21, 2006, 06:21:28 PM »
I followed all the links and took my trigger apart and did all the magic work.  Now it breaks at a clean and measured 12-14 oz.  A bit lighter than I wanted but it works just fine.  It is now no longer a hunting rifle only a bench rester.  Don
Logged
Luke 11:21

Offline Hunternz

  • GBO Supporter
  • Trade Count: (0)
  • Member
  • *****
  • Posts: 86
  • Gender: Male
Trigger work
« Reply #7 on: February 21, 2006, 10:16:35 PM »
Thanks Guys,
my H&R favourites list continues to grow.
Regards Howard.
Logged
Pages: [1]   Go Up
« previous next »