Author Topic: Flyrod advice....  (Read 970 times)

0 Members and 1 Guest are viewing this topic.

Offline flintlock

  • Trade Count: (0)
  • Senior Member
  • *****
  • Posts: 1405
  • Gender: Male
Flyrod advice....
« on: May 23, 2006, 05:48:35 AM »
I'm in the market for a new flyrod...the one I have been using is 35+ years old....Its a fiberglass bass bugging rod, that my dad owned and never got the hang of, I started using when I was 13 or so, have caught tons of bass and bream  with but I want something lighter....I'm thinking of a 5-6 weight in 8 1/2 to 9 feet....I fish out of a boat, around cypress trees and lily pads in the eastern rivers of NC....would like to be able to cast smaller bass bugs,but my primary target is bream...I also play to buy an extra spool for sinking line.

Is a 6wt light enough to have fun with bream??? Or should I go with a 5wt...
Is a 5wt heavy enough for smaller bass bugs??? Can a 5wt handle sinking fly line??

I'm also looking at a 4 piece, so I can keep in a case in the boat for when I need it. I have been told that multiple piece rods don't have "flat spots" at the junctions like they did years ago...Is this correct??

Offline tscott

  • Trade Count: (1)
  • A Real Regular
  • ****
  • Posts: 561
Flyrod advice....
« Reply #1 on: May 23, 2006, 06:28:24 AM »
Try the Powell Rod Company in California. They will help you, and I have had them make me rather inexpensive rods.

Offline Black_Wolf

  • Trade Count: (0)
  • Member
  • *
  • Posts: 85
Flyrod advice....
« Reply #2 on: May 23, 2006, 01:06:10 PM »
You could try a St Croix 5 weight 9 foot 4 piece Legend Ultra. Sounds just like what you are looking for. You could get the 5 weight and it will do what you are asking but i would go with a 6 weight. I have one in 6 weight and small fish are still fun but it has plenty of back bone if you get a good fish on. Either weight would be good though.

Offline flatlander

  • Trade Count: (3)
  • A Real Regular
  • ****
  • Posts: 578
Flyrod advice....
« Reply #3 on: June 16, 2006, 02:26:15 AM »
I'd fish for bluegills using a 2 or 4 weight. Lots of fun! I'd personally lean to a 3 or 4 weight if you are using the rod for bream only.

Offline Tapper

  • Trade Count: (0)
  • Member
  • *
  • Posts: 34
5 vs 6 wt rod
« Reply #4 on: June 24, 2006, 10:35:58 AM »
Flintlock,
I think that a moderately fast action 5 or 6 wt, 9' rod would do what you are asking of it. For your comparison, I use a St Crox 9', 5 wt, model AF905 Avid (2 pc) fly rod for most of my larger trout stream fishing and small bass fishing. It is a moderate power rod with good line speed. It easily handles double fly set ups, or a dry fly on top with a small split shot and nymph under, yielding good distance and sure turnover. Since you will be casting from a boat, you can adjust the distance requirement easier than we can sometimes when wading, so consider a rod with good power for the solid turnover. One other note: While both weights will do the job for you, I will recommend that you give special consideration to casting in windy conditions, and to line choice.
The 6 wt will do better in the wind than the 5. This may not be a factor for you, but I thought I'd remind you.
I use a Scientific Angler's GPX WF Floating on the 5 wt rod. It has a short taper and strong turnover capabilities. I use a Cortland 444 Si ghost tip as a sink tip line when I need to. This rods does well with both. If I need 'delicate', I either back off the cast, or go to a lighter weight rod/line. SA's XXD might be a good choice for your application, or Cortland's 444 Lazer Line.

Hope this helps,

Tapper