Author Topic: front sight height  (Read 397 times)

0 Members and 2 Guests are viewing this topic.

Offline hunterwinco

  • GBO Supporter
  • Trade Count: (1)
  • Avid Poster
  • *****
  • Posts: 162
front sight height
« on: August 17, 2006, 03:36:51 PM »
I can't seem to use the search function tonight, so I thought I would ask...I have a 22 hornet (std) and last night I mounted a peep sight on it.  My problem is I can't bring my group down.  I am assuming that I need a higher front bead.  Does NEF make a taller one than on the hornet barrel?

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: front sight height
« Reply #1 on: August 17, 2006, 03:57:36 PM »
A quick call to em tomorrow should answer that question. A Williams firesight on a shorty ramp may also work, see the Peep and Firesights link in the FAQ. ;)

Tim
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Doc4570

  • Trade Count: (0)
  • Member
  • *
  • Posts: 11
Re: front sight height
« Reply #2 on: August 17, 2006, 04:00:04 PM »
HI Hunterwinco,
   There is a lot of good info about peep sights in the FAQ section
at the top of the page.
I think the .22 Hornet front sight is the highest NEF makes.
I bought the replacement sight the FAQ section recommends,
but being ham-fisted I screwed it up.
(Don't move the bead over in the dovetail with a hammer. (Duh!))
Eventually, I put a 1/16" shim (kydex) under the original front sight and used a
longer screw.  It works with the 45 grain factory loads, but the
lighter Hornady loads are still about 3" high at 50 yards.
Hope this helps.
(Don't forget about the hammer :) )
Doc

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: front sight height
« Reply #3 on: August 17, 2006, 04:06:33 PM »
Williams has instructions on how to figure out sight height on page 18 of their catalog.

Tim


http://www.williamsgunsight.com/gunsights/pdf/WilliamsLoRes.pdf
"Always do right, this will gratify some and astonish the rest" -  Mark Twain

Offline Doc4570

  • Trade Count: (0)
  • Member
  • *
  • Posts: 11
Re: front sight height
« Reply #4 on: August 17, 2006, 04:32:22 PM »
The one thing I didn't like about the Shorty Ramp is that the screw
is under the dovetail, so you need access to a sight pusher tool.
If the sight base loosens up, you have to remove the sight insert
to tighten it up.

In NYC, you'll find an honest politician before you'll find a gunsmith :)

Doc

Offline quickdtoo

  • Global Moderator
  • Trade Count: (149)
  • Senior Member
  • *****
  • Posts: 43301
  • Gender: Male
Re: front sight height
« Reply #5 on: August 17, 2006, 04:47:57 PM »
I thought that too, I checked out sight pushers, they're $40-$60, ended up just bucking up the ramp and knocking the sight insert out with a brass drift, they can be installed with a vise or vise-grips. It takes a little jury rigging to buck the ramp up, but it can be done. A little loctite on the screw before the install will keep it from loosening up. ;)

Tim

http://www.midwayusa.com/eproductpage.exe/showproduct?saleitemid=754137

http://www.midwayusa.com/eproductpage.exe/showproduct?saleitemid=732798
"Always do right, this will gratify some and astonish the rest" -  Mark Twain