Author Topic: Let's see some Handis (Read 86587 times)

cwlongshot · « **Reply #180 on:** August 31, 2008, 11:07:19 AM »

I promised some more pics...

I swapped the stocks on the Shariki to a set of straight lams, I picked up here some years back. I also got rid of the gawd awful sites that came on the thing!!

Here is a LMT slug I had shown before, only now its got new to it wood. Its an older 60's receiver and had allot of drop. The Monte Carlo allows my eye to directly line up with the open sites.

Lastly is another one you have seen before only again with new to it wood!! Its my 280/25-06/223. THX PHATINJUN!!!

I saw a beautiful, brandy new, 357mag syn this past weekend... ALMOST had to have it....

CW

rbergum95 · « **Reply #181 on:** September 14, 2008, 11:10:30 AM »

ok, ill play. this one started out as a with a simple question, "would you hunt with a pink rifle?" my answer was yes. it then moved onto a wager if i were to build or buy a pink rifle, the man placing the wager would have to hunt with it during the 2008 deer season, plus a small cash prize. well, here it is....anyone think he will hunt with it?? doesnt matter, i wont let him hunt with it anyway. but i will take the cash.

either way, it may be just the ticket to get my niece to satart shooting. if not, ill just use it as my new bobcat buster. (pun intended)
the pictures dont really do it justice, it is way brighter than what it looks.

hellooooooooooooo kitty !!!!!!!!!!!!!!
.22-250 standard barrel
simmons 3-9x40 scope

stimpylu32 · « **Reply #182 on:** September 14, 2008, 11:33:41 AM »

I like it

, I have even been known to wear a pink shirt a time or two , being 6-1 / 285 most tend to not question my manhood .

stimpy

petemi · « **Reply #183 on:** September 14, 2008, 12:08:33 PM »

I love it!! If you want to sell it, let me know, I'll buy it for Tim or Stimpy for Christmas!!!

Hey Stimpy, Why does that Viagra ad keep following you around?

quickdtoo · « **Reply #184 on:** September 14, 2008, 12:11:36 PM »

Nice work rbergum95, I have a 5 yr old grand daughter that might just have to have one like that!!

Tim

PHATINJUN · « **Reply #185 on:** September 14, 2008, 12:44:13 PM »

Some how I just knew Stimpy would be the fist to post on that . Kurt

cwlongshot · « **Reply #186 on:** September 14, 2008, 12:57:55 PM »

Quote from: rbergum95 on September 14, 2008, 11:10:30 AM

ok, ill play. this one started out as a with a simple question, "would you hunt with a pink rifle?" my answer was yes. it then moved onto a wager if i were to build or buy a pink rifle, the man placing the wager would have to hunt with it during the 2008 deer season, plus a small cash prize. well, here it is....anyone think he will hunt with it?? doesnt matter, i wont let him hunt with it anyway. but i will take the cash.

either way, it may be just the ticket to get my niece to satart shooting. if not, ill just use it as my new bobcat buster. (pun intended)
the pictures dont really do it justice, it is way brighter than what it looks.

hellooooooooooooo kitty !!!!!!!!!!!!!!
.22-250 standard barrel
simmons 3-9x40 scope

Kinda cute... Nice work!!

CW

rbergum95 · « **Reply #187 on:** September 14, 2008, 02:31:24 PM »

thanks for the replies guys. i will have to see how it is recieved on the local range one busy saturday afternoon. it is sure to turn some heads!!

ron

Hofs01 · « **Reply #188 on:** September 24, 2008, 10:53:38 AM »

Thought it was time for a new Family picture.

PHATINJUN · « **Reply #189 on:** September 24, 2008, 12:05:40 PM »

Very nice Brian that gives me an idea I've been wanting to take a family photo myself I think if I take 2 one with Muzzleloaders and pistol calibers and the other with rifle calibers I could get them in. I will need to send the wife out for the day though cause she will freak if she see's them all in one place at one time. Kurt

quickdtoo · « **Reply #190 on:** September 24, 2008, 12:40:25 PM »

Lookin good Brian!!

cjclemens · « **Reply #191 on:** September 24, 2008, 05:04:32 PM »

Here's a bad pic of my .223. All original with a Bushnell Banner scope on it. I have a BC and a .410 in the safe at my folk's place.

sonofafish · « **Reply #192 on:** November 06, 2008, 12:02:02 PM »

Holly smokes they look dandy

Clayne_b · « **Reply #193 on:** November 09, 2008, 11:13:55 AM »

.223 ultra

25-06 ultra

.223 and 25-06 together. .223 is the top pic

handi, .243 .22 20guage

jwiedmayer · « **Reply #194 on:** November 19, 2008, 03:19:42 PM »

This is mine almost completed.

Josh M. · « **Reply #195 on:** November 19, 2008, 03:38:32 PM »

Quote from: jwiedmayer on November 19, 2008, 03:19:42 PM

This is mine almost completed.

Where did you get that stock?
How heavy is it? - JM.

Wakaba · « **Reply #196 on:** November 19, 2008, 05:15:35 PM »

Quote from: Josh M. on November 19, 2008, 03:38:32 PM

Where did you get that stock?
How heavy is it? - JM.

http://www.gunstocksinc.com/web_pages/Plate-pics/NEF-stocks/Handi-rifle-stocks.htm

skifastchad · « **Reply #197 on:** November 20, 2008, 04:11:02 AM »

I finally finished my project just in time for this year's muzzleloader season.

This started as a stainless/synthetic sidekick.
I got rid of the synthetic stock, and put a straight grip cinnamon laminate shotgun stock set on it. The existing forend screw hole was filled with clear resin, and I milled a new one farther forward to fit the sidekick. I then milled out a ramrod channel inside the bottom of the forend, and put in a retaining spring. The front of the forend had to be shortened just under an inch, since the ramrod hole was deeper than the front of the forend was thick.
After finishing the stock, I went to work on the frame. The pins on a nickel frame are stainless, and polish very easily. 10 minutes on a buffing wheel, and they were all shiny. The frame surface itself is a different story. The nickel plating is very thin, and doesn't shine up very easily. I used some mothers mag polish and a rag, and shined it up as best I could.
The barrel was the easiest part, but the most time consuming. I spent about 2 hours (just a few minutes here and there) wet sanding the bead blasted finish off the barrel, starting with 400, then 600 and 800 wet sand paper. For the finishing polish, I turned some short 1" dowels to fit tight in the breech and muzzle, then clamped it in a wood lathe, and let it spin while polishing it with a rag and almost a whole can of mag polish.
The barrel is like a mirror. If Santa brings me a new camera for Christmas, I'll get some better close-up shots.

navylawdog · « **Reply #198 on:** November 20, 2008, 05:34:39 PM »

Quote from: jwiedmayer on November 19, 2008, 03:19:42 PM

This is mine almost completed.

Did you order the stock with the recoil pad already installed or did you fit it yourself? If you did it yourself what one did you buy? I have the same stock and would like to put a recoil pad on it but I didn't know what size to get ie., if they make one the correct size or if I would have to fit it.

Navylawdog

quickdtoo · « **Reply #199 on:** November 20, 2008, 05:40:01 PM »

GSI uses grind-to-fit pads, depends on which one ya want.

Tim

http://www.gunstocksinc.com/web_pages/Recoil-pads.htm

Bayou Stalker · « **Reply #200 on:** November 21, 2008, 03:11:21 AM »

Here are my two:

Top is myy daughters 410 Tamer. This stock is the perfect youth stock IMHO.

Bottom is my 45/70. It has a Boyd's thumb hole stock, Burris 4X20 scope in Zee low rings, cut down hammer to clear the scope, and a backordered matching forend. The existing forend has had the o-ring treatment.

navylawdog · « **Reply #201 on:** November 21, 2008, 04:34:06 PM »

Quote from: quickdtoo on November 20, 2008, 05:40:01 PM

GSI uses grind-to-fit pads, depends on which one ya want.

Tim

http://www.gunstocksinc.com/web_pages/Recoil-pads.htm

Thank Tim I will have to add that to my CHRISTmas wish list I guess.

Navylawdog

KYJoe · « **Reply #202 on:** November 28, 2008, 01:04:43 PM »

This is my UVF in 22-250 caldwell bipod,banner6-24x,cheekpeice.

Bayou Stalker · « **Reply #203 on:** December 13, 2008, 04:04:52 PM »

An update on mine...

45/70 with the cinnamon laminate stock, and my new Ultra SS .444 wearing the camo laminate set.

OBXPilgrim · « **Reply #204 on:** December 14, 2008, 04:58:58 AM »

Quote from: PPCFlyer on November 21, 2008, 03:11:21 AM

Here are my two:

Top is myy daughters 410 Tamer. This stock is the perfect youth stock IMHO.

Bottom is my 45/70. It has a Boyd's thumb hole stock, Burris 4X20 scope in Zee low rings, cut down hammer to clear the scope, and a backordered matching forend. The existing forend has had the o-ring treatment.

Ah yes, the tamer stock.

I bought one to put on my new 30-06/444/223/50ML set. It works great with a limbsaver slip on pad. I also found that with my full bundle of winter hunting clothes on, if I slip the pad off, eye relief is back to where it needs to be.

Big Blue · « **Reply #205 on:** December 15, 2008, 12:59:17 PM »

Beautiful rifles and a lot of inspiration to be found here. Thanks to all for sharing them.
Don

RelicHound · « **Reply #206 on:** December 15, 2008, 04:21:37 PM »

wow I almost feel out of place posting this next to all the beautiful guns here but my collection will grow over time now that I have gotten my feet wet with these guns.

this is my handi chambered in 22 hornet.

cwlongshot · « **Reply #207 on:** February 07, 2009, 03:50:29 PM »

All you guys have some REALLY nice handis there!!

Keep the pics coming, how about some more UPDATES from the guys that already posted?

Speaking of updates. I haven't updated my post since '07.. So I just went added some new pics.

CW

pitman_mm · « **Reply #208 on:** March 08, 2009, 06:48:54 PM »

My first but probably not my last.

45-70 w/ 16" fluted barrel, fiber optic sights and muzzle brake.

Singleshotsam · « **Reply #209 on:** March 09, 2009, 07:49:41 AM »

Here is my .223 w/ a choate varmint set and BSA 3.5 - 10 x 50...